SET CONTENTS AND RATINGS
(Specifications are subject 10 change without prior notice.) Operating System
Transmitter
Receiver
Servo
NiCad Battery
Switch
Others
CONOUEST
FP-6NLK
FP T6NLK x 1 FP-T4NL x 1
FPR7Hx1 FP.R4Fx 1/FP-R4HX 1
FP-S38 x 4
NR
4M
x
SSW-Hx
Charger. Frequency flag
Mounting screw.
CONQUEST
FP-4NL
FP
S38
x
3
1
1
. Spare horn,
TRANSMITTER FP-T6NLK /T41ML
2 stick,servo reverse
Aileron, Elevator dual
switch. Landing gear
switch (5ch) & switch
(6ch) 6NLK only
Transmitting frequency : 72MHz bands, 75MHz
bands
Modulation system : AM
Power requirement : 9, 6V, NiCad battery
(NT-8LP)
Current drain : 190mA
RECEIVER FP-R7H / R4F/ R4H
Receiving frequency : 72MH/ bands, 75MHz bands
Crystal replacement system: Frequency can be changed
within the same frequency
band by changing the pre-
cision crystal.
Intermediate frequency : 455kHz
Power requirement : 4, 8V, NiCad battery
Common use with servo
Current drain : 4.8V, 10mA
Dimensions
R7H 1.6x 2.6 x 0.8 inch
(41
x
69
x
21
mm)
R4F 1.6 x 2.3 x 0.7 inch
(40.2
x
58.5
x
19
mml
R4H 1.26x 2.05 x 0 77 inch
(32
x
52
x
19.4
mm)
Weight
R7H
1 7oz(50g)
R4F
1.6oz
(46g)
R4H
1.06oz (30g)
Receiving range : 550 yards (500m) on the
ground. 1,100 yards
(1,000m) in the air.
(at the best conditions)
Throttle trim
lever
SERVO FP-S38
Control system : + pulse width control
Operating angle : One side 45° or more
(including trim)
Power requirement : 4.8V ~ 6V
Current drain (IDLE) : 6.0V, 8mA
Output torque : 34.8oz.in (2.5kg-cm)
Operating speed : 0.23sec/60°
Dimensions : 1.59 x 0.79 x 1.38 inch
(40.5 x 20 x 35.3mm)
Weight : l.44oz (41g)
6th CH switch (6NLK only)
Aileron dual switch (6NLK only)
Neck strap bracket
Rudder
trim lever
Rudder
Nonslip adjustable
lever head
Aileron
Elevator
In the following descriptions, all the servo reversing switches
are assumed to be in the normal position. When they are in the
reverse position, operation is the opposite of that described.
23) Battery cover
Elevator
trim lever
Aileron
trim
lever
Charging
jack
Transmitter
NiCad battery
NT-8LP
Power switch
Servo reversing
switches
Fig.
1
Throttle
Level meter
Elevator
dual switch
(6NLK only)
Landing gear switch
(5ch) (6NLK only)
(6NLK only)
Elevator dual trimmer
Handle
Aileron
dual
trimmer
Antenna
TRANSMITTER FP-T6NLK/T4NL CONTROLS
Fig. 1 shows the name of each part of the transmitter.
Memorize the position and operation of each
switch and control.
Aileron
Elevator
Throttle
Rudder
Aileron operation
Elevator operation
Throttle operation
Rudder operation
Landing gear switch
(6NLK only)
Raising and lowering the
landing gear.
6chCH switch (6NLK only)
Use for controlling model
airplane flaps, etc. The
The servo is connected
to 6 channels.
Fig.
2
Aileron trim lever Aileron trimmer
Elevator
trim
lever
Elevator
trimmer
Throttle trim lever Throttle trimmer
Rudder trim lever Rudder trimmer
Aileron dual rate switch (6NLK only)
Aileron dual rate ON-OFF switch. When set to the upper
position, dual rate is turned on, and when set to the lower
position, dual rate is turned off.
Aileron dual rate trimmer (6NLK only)
This trimmer sets the aileron travel when the aileron dual
switch is set to on. When the dual switch is set to ON, the
servo throw can be set to an arbitrary angle smaller than
when the dual switch is OFF (normal) as shown in the
figure. Use the throw matched to the aircraft and the
maneuvers to be performed.
servo is operated at the
and
positions. The
position is off.
Praat mee over dit product
Laat hier weten wat jij vindt van de Futaba FP-6NLK RC Controller. Als je een vraag hebt, lees dan eerst zorgvuldig de handleiding door. Een handleiding aanvragen kan via ons contactformulier.