Handleiding Hitec Flash 8 RC Controller

Handleiding

8 Channel 2.4 GHz Aircraft Computer Radio System8 Channel 2.4 GHz Aircraft Computer Radio System

Section 1: Introduction Section 1: Introduction

20 21

Optima and Minima Series Receiver Link (ID-Setting or Bind) cont.

When the binding process is completed, it

automatically goes to the nish screen. (The

BLUE and RED LEDs will be solidly on)

When the LED stops blinking, press the jog

dial to get to the next screen. The blue LED

will glow solid.

Turn the power to the receiver o, then back on. Check for a solid blue LED light. Once on, press the jog dial

to FINISH the binding process. Make sure all functions are working properly before ying your model.

If any function is not working as described, please go back to step 6 and repeat the

binding again.

If all functions work well, press the Finish icon on the screen to nish binding.

FAIL-SAFE and Hold Mode Setup

If the FAIL-SAFE function is set up and used properly but the receiver signal is somehow interrupted,

the servos will move to your previously stored FAIL-SAFE setup. If you do not activate the FAIL-SAFE

function, the signal is switched o after the HOLD period of 1 sec. This means that the servos become

“soft” and remain in their last commanded position under no load (this may equate to full-throttle!) until

a valid signal is picked up again. In the interest of safety, we recommend that FAIL-SAFE should always

be activated, and the FAIL-SAFE settings should be selected so as to bring the model to a non-critical

situation (e.g. motor idle / electric motor OFF, control surfaces neutral, airbrakes extended, aero-tow

release open, etc.).

Testing the FAIL-SAFE Setting

Move the sticks to positions other than the FAIL-SAFE settings, and then switch o the transmitter. The

servos should now move to the FAIL-SAFE positions previously stored after the one second HOLD period.

How to turn FAIL-SAFE O and reactivate the Hold Mode

a. Switch on the transmitter, then the receiver. Wait for the system to boot and you have control over the

model.

b. Press and hold the receiver function button for 6 seconds and release it. After 2 seconds, the red and

blue LEDs will blink rapidly.

c. Immediately press the receiver function button once.

d. FAIL-SAFE Mode is now deactivated and HOLD mode is activated.

e. Turn the transmitter o, then the receiver o.

f. Turn the system back on to use it.

Fail-Safe position

Switch on both.

Wait for the system to boot and you have

control over the model.

(approx. 6 second)

Release the button. After 2 seconds both red and blue LEDs blink alternately.

The receiver will count 5 seconds. During that time, move all the transmitter

sticks and other controls to the desired FAIL-SAFE positions (e.g. motor idle,

control surfaces neutral), and hold until the blinking stops.

When the blinking stops, the system will temporarily

the system to save and exit.

www.hitecrcd.com

2Sec.

6Sec.

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Hitec Flash 8 RC Controller. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Hitec. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Hitec Flash 8 RC Controller in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Hitec RC Controllers
Meer handleidingen voor RC Controllers

Beoordeling

Gerelateerde producten

Handleiding

Hitec Optic 5 RC Controller

Handleiding

Hitec Aurora 9X RC Controller

Handleiding

Hitec Flahs 7 RC Controller

Handleiding

Hitec Aurora 9 RC Controller

Handleiding

Futaba FP-6FN RC Controller

Handleiding

Futaba 9CAF Super RC Controller

Handleiding

Futaba 8UAFS RC Controller

Handleiding

Graupner MX-10 RC Controller

Gerelateerde categorieën