8 Channel 2.4 GHz Aircraft Computer Radio System8 Channel 2.4 GHz Aircraft Computer Radio System
Section 1: Introduction Section 1: Introduction
18 19
Optima and Minima Series Receivers cont.
Compatibility:
The OPTIMA & MINIMA receivers are compatible with transmitters using the Hitec AFHSS 2.4 GHz system,
such as, Spectra 2.4 module or dedicated built-in module AFHSS 2.4 Hitec transmitters.
FAIL-SAFE/Hold Mode Selectable:
Servos and other accessories can be set with a FAIL-SAFE point if power to the receiver is lost.
Jumper*:
The jumper is installed at the factory and is used when the receiver is powered by an electronic speed
control, a commercially available B.E.C. (battery eliminator circuit), dedicated 4.8 to 6V. NiMH battery pack,
or regulated Li-Po battery. The jumper is removed when the receiver is powered using the SPC feature.
*These functions/ features are only for OPTIMA series receivers.
Common Receiver Connection Diagrams
Electric powered aircraft with Electronic Speed Control: This conguration is appropriate for electric
planes using ESCs providing power to the receiver and servo functions.
BAT/CH7
CH6
DATA
SPC
LED
LINK
LED
LINK
CH1
CH2
CH3
CH4
CH5
OPTIM A 7OPTIMA
7
2.4GH
z 7 Channel Aircraft Receiver2.4GHz 7 Channel Aircraft Receiver
AFHSS
2.4GHz
Telemetric
ADAPTIVE
FREQUENCY HOPPING
SPREAD SPECTRUM
SERVO
SERVO
SERVO
SERVO
SERVOS ERVO
Power Battery
Motor
BEC
ESC
SERVO
SERVOS ERVO SERVO
Power Battery
Motor
SERVO
BEC
ESC
2.4GHz 6 Channel
Aircraft Receiver
Glow, gas or electric powered aircraft using a separate receiver battery supply: Follow this connection
diagram when using a regulated Li-Po, or 4.8 to 6V receiver battery.
BAT/CH7
CH6
DATA
SPC
LED
LINK
LED
LINK
CH1
CH2
CH3
CH4
CH5
OPTIM A 7OPTIMA 7
2.4GHz 7 Channel Aircraft Receiver2.4GHz 7 Channel Aircraft Receiver
AFHSS
2.4GHz
Telemetric
ADAPTIVE
FREQUENCY HOPPING
SPREAD SPECTRUM
SERVOSERVO
SERVO
SERVOS ERVO
Receiver
Battery
SERVO
Engine
SERVOSERVOS ERVO SERVO
Receiver
Battery
SERVO
Engine
2.4GHz 6 Channel
Aircraft Receiver
2.4GHz 6 Channel
Aircraft Receiver
OPTIMA
MINIMA (MAXIMA)
2.4GHz 6 Channel
Aircraft Receiver
Optima and Minima Series Receiver Link (ID-Setting or Bind)
Your Hitec AFHSS system uses a communication protocol that links and binds the Hitec 2.4GHz receiver to
your transmitter. Once the receiver and transmitter are “bound”, no other transmitter can interfere.
Turn on the transmitter and select “Yes” to the “Ready to Transmit” prompt by
pressing the jog dial.
Press the jog dial and back button simultaneously to enter the System
Menu list. From here scroll to the SPECTRA function and press the jog
dial to enter the Spectra setup menu.
Press the jog dial to
activate the receiver
selection and scroll
to the “Opti&Mini”
receiver.
Back at the receiver
selection screen, scroll
to BINDING and press
the jog dial to enter
the binding screen.
Select the type of receiver
you are using, either
Optima or Minima, and
push the jog dial to
conrm your selection.
Press the jog dial to save your
setting. When prompted to
change the receiver type select
“Yes” and press the jog dial to
conrm your choice.
Select “Yes” for binding.
Press and hold the link button on the Receiver and turn on the power.
Release the link button. Release the Link button, both RED and
BLUE LEDs will be blinking rapidly to
nd the transmitter’s signal.
Praat mee over dit product
Laat hier weten wat jij vindt van de Hitec Flash 8 RC Controller. Als je een vraag hebt, lees dan eerst zorgvuldig de handleiding door. Een handleiding aanvragen kan via ons contactformulier.