Handleiding Hunter 19085 Squire Manor Lamp

Handleiding

INSTALLATION INSTRUCTIONS

INSTRUCCIONES DE INSTALACIÓN / INSTRUCTIONS D’INSTALLATION

READ AND SAVE THESE INSTRUCTIONS

These instructions are provided for your safety.

It is very important that they are read carefully

and completely before beginning installation

of the lighting xture.

•

WARNING

• To avoid possible electrical shock, before

installing your light xture, disconnect the power

by turning off the circuit breakers to the outlet box

associated with the wall switch location.

• The lighting xture must be grounded. If the

ground wire for the installation site is not present,

immediately STOP installation and consult a

qualied electrician.

• All wiring must be in accordance with national

and local electrical codes ANSI/NFPA 70. If you

are unfamiliar with wiring or in doubt, consult a

qualied electrician.

LEA Y GUARDE ESTAS INSTRUCCIONES

Estas instrucciones se proporcionan para

su seguridad. Es muy importante leerlas

detenidamente y completamente antes de

comenzar la instalación de la lámpara.

•

•

Para evitar una posible descarga eléctrica, antes

de instalar su lámpara, desconecte la energía

apagando los interruptores automáticos (breakers)

que alimentan la caja de salida asociada con la

ubicación del interruptor de pared.

• L’appareil d’éclairage doit être mis à la terre.

Si le l de terre du lieu d’installation n’est pas

présent, ARRÊTEZ immédiatement l’installation

et consultez un électricien qualié.

• Todo el cableado debe realizarse de acuerdo

con los códigos eléctricos locales y nacionales

ANSI/NFPA 70. Si no está familiarizado con

el cableado, o si tiene duda, consulte a un

electricista calicado.

ADVERTENCIA

LISEZ ET CONSERVEZ CES INSTRUCTIONS

Ces instructions sont fournies pour votre

sécurité. Il est très important de les lire

attentivement dans leur intégralité avant

d’entreprendre l’installation du luminaire.

•

AVERTISSEMENT

• Pour éviter tout choc électrique, avant

d’installer le luminaire, coupez le courant en

éteignant les disjoncteurs de la boîte électrique

associée à l’interrupteur mural.

• Le luminaire doit être mis à la terre. Si le l

de terre du lieu d’installation n’est pas présent,

ARRÊTER immédiatement l’installation et

consulter un électricien qualié.

• Tout le câblage doit être conforme aux codes

électriques nationaux et locaux en vigueur et

à la norme ANSI/NFPA70. Si vous n’avez pas

l’habitude de faire ce câblage ou en cas de doute,

adressez-vous à un électricien qualié.

ENGLISH

For Models:

Para los Modelos:

Pour les Modèles:

Squire Manor

Here are the

tools you’ll

need to

complete your

installation:

Estas son las

herramientas

que usted

necesitará para

completar su

instalación:

Voici les outils

dont vous

aurez besoin

pour réaliser

l’installation:

Twist or tape wire

ends together to make

it easier to thread

through downrod.

Hunter Pro Tip:

NOTICE

In order to use a 12in rod by itself

you must rst remove the post

from the 6in rod and install it on

one of the ends of the 12in rod.

Screwdriver

Destornilladore

Tournevis

4 Light Lantern Pendant

4 Luz FarolColgante

4 Lumière Lanterne Chaînette

Wire Strippers

Pelacables

Pince à dénuder

Pliers

Alicates

Pince

Ladder

Escalera

Échelle

PREPARING FOR INSTALLATION

Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old

xture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the

bag. One end of the threaded post (F) should be attached to the mounting bracket (A) with a washer (D) and a hex nut

(E) in place. The other end should have the canopy loop (H) attached. Unscrew the canopy loop ring (I) from the canopy

loop (H). Depending on the placement of your junction box the position of threaded post (F) may need to be adjusted

to allow the canopy to be ush with the ceiling. Determine this by lifting mounting bracket (A) up to the junction box

and place canopy (G) over the canopy loop (H), so that it is ush with the ceiling. Adjust the position of threaded post

(F) on the mounting bracket (A) so that the canopy (G) covers at least half of the exterior threads on the canopy loop

(H) while it is securely connected to threaded post (F). The threaded post (F) can be adjusted by loosening hex nut (E)

to allow movement of threaded post (F) on mounting bracket (A). Once the ideal position of the threaded post (F) is

determined, tighten up the hex nuts (E) onto the threaded post (F) just beneath the mounting bracket (A) to secure the

threaded post in place.

ASSEMBLING THE FIXTURE

There are 4 12-inch rods (K), and 1 6-inch rod (L) included for each xture. Determine the correct number of rods needed

for proper hanging height. To lengthen the xture, add additional rods. To shorten the xture, trim the wires to desired

length. Leave at least 8 to 10 inches of wire in addition to the desired length and slide any excess rods off the xture’s

wiring to discard. Keep in mind that you must use at least one rod to hang the xture. Thread the wires through the rods

and pull the wires until taut before connecting the rods together. All threads should be engaged but do not overtighten

(some manual straightening of the downrods may be required). Place cup (M) onto threaded post (N) and screw rod onto

threaded post (N) on the xture. Pull the xture wires through the canopy loop ring (I), top of canopy (G), and canopy

loop (H). Screw the top rod to canopy loop (H) of canopy (G). Have a helper support the xture’s weight and attach the

mounting bracket (A) to the junction box by securely tightening the mounting screws (B).

CONNECTING THE WIRES

Attach the xture’s wires to the power supply wires from the junction

box. Connect black to black (Live); white to white (grounded); grounding

to grounding (green or copper). Twist the ends of the wire pairs together.

Then, twist on a wire connector. Make sure all twists are in the same

direction. Loop xture’s ground wire around grounding screw (C) and

tighten. If there is no ground wire (green or copper) from the junction

box, contact a qualied electrician.

FINISHING THE INSTALLATION

Place the canopy (G) ush to the ceiling and slide the canopy loop ring (I) up beneath the canopy. Tightly screw canopy

loop ring (I) onto the canopy loop (H) to properly secure the canopy (G) in place. Slide candle sleeves (O) onto sockets

(P). Install light bulbs (not included) in accordance with the xture’s specications. Do not exceed the recommended

wattage. Your installation is now complete. Turn on the power and test the xture.

CLEANING TIPS

Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light

and wipe down the xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.

19084

19085

19480

©2022 Hunter Fan Co. ML033

r_022222

2.27 lbs (1.03 kg)

Fixture weight ±2 lbs:

Peso ±2 lbs:

Poids xe ±2 lbs:

Part #/Pieza #/Pièce #

Hardware Service Kit / Kit De Mantenimiento Del Equipo /

Trousse De Maintenance Quincaillerie

Finish/Finish/FiniModel/Modelo/Modèle

For Models:

Para los Modelos:

Pour les Modèles:

KC02902119

KC02901214

KG20702199

Brushed Nickel

Níquel Pulido

Nickel Brossé

Chrome/Cromo/Chrome

Matte Black

Negro Mate

Noir Mat

19084

19085

19480

D

E

F

A

B

G

H

C

J

L

K

M

I

N

O

P

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Hunter 19085 Squire Manor Lamp. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Hunter. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Hunter 19085 Squire Manor Lamp in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Hunter Lampen
Meer handleidingen voor Lampen

Veelgestelde vragen over Hunter 19085 Squire Manor Lamp

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Hunter 19712 Lochemeade Lamp

Handleiding

Hunter 19258 Cypress Grove Lamp

Handleiding

Hunter 19215 Bluff View Lamp

Handleiding

Hunter 19390 Gablecrest Lamp

Handleiding

Hunter 19332 Langwood Lamp

Handleiding

Hunter 19978 Felippe Lamp

Handleiding

Hunter 19333 Langwood Lamp

Handleiding

Hunter 19967 Astwood Lamp

Gerelateerde categorieën