Handleiding Hunter 19094 Gablecrest Lamp

Handleiding

INSTALLATION INSTRUCTIONS

INSTRUCCIONES DE INSTALACIÓN/ INSTRUCTIONS D’INSTALLATION

For Models:

Para los Modelos:

Pour les Modèles:

Here are the

tools you’ll

need to

complete your

installation:

Estas son las

herramientas

que usted

necesitará para

completar su

instalación:

Voici les outils

dont vous

aurez besoin

pour réaliser

l’installation:

Ladder

Escalera

Échelle

Screwdriver

Destornilladore

Tournevis

Pliers

Alicates

Pince

Wire Strippers

Pelacables

Pince à dénuder

READ AND SAVE THESE INSTRUCTIONS

These instructions are provided for your safety. It

is very important that they are read carefully and

completely before beginning installation of the

lighting xture.

LEA Y GUARDE ESTAS INSTRUCCIONES

Estas instrucciones se proporcionan para su

seguridad. Es muy importante leerlas detenid-

amente y completamente antes de comenzar la

instalación de la lámpara.

LISEZ ET CONSERVEZ CES INSTRUCTIONS

Ces instructions sont fournies pour votre sécurité.

Il est très important de les lire attentivement dans

leur intégralité avant d’entreprendre l’installation

du luminaire.

Fixture weight ±2 lbs:

Peso ±2 lb:

Poids xe ±2 lbs:

•

WARNING

• All wiring must be in accordance with national

and local electrical codes ANSI/NFPA 70. If you

are unfamiliar with wiring or in doubt, consult a

qualied electrician.

• To avoid possible electrical shock, before

installing your light xture, disconnect the power

by turning off the circuit breakers to the outlet box

associated with the wall switch location.

• The lighting xture must be grounded. If the

ground wire for the installation site is not present,

immediately STOP installation and consult a

qualied electrician.

• Todo el cableado debe realizarse de acuerdo con

los códigos eléctricos locales y nacionales ANSI/

NFPA 70. Si no está familiarizado con el cableado,

o si tiene duda, consulte a un electricista calicado.

• Para evitar una posible descarga eléctrica, antes

de instalar su lámpara, desconecte la energía

apagando los interruptores automáticos (breakers)

que alimentan la caja de salida asociada con la

ubicación del interruptor de pared.

•

ADVERTENCIA

• L’appareil d’éclairage doit être mis à la terre.

Si le l de terre du lieu d’installation n’est pas

présent, ARRÊTEZ immédiatement l’installation et

consultez un électricien qualié.

•

AVERTISSEMENT

•

Tout le câblage doit être conforme aux codes

électriques nationaux et locaux en vigueur et à la

norme ANSI/NFPA70. Si vous n'avez pas l'habitude

de faire ce câblage ou en cas de doute, adressez-

vous à un électricien qualié.

• Pour éviter tout choc électrique, avant d’installer

le luminaire, coupez le courant en éteignant les

disjoncteurs de la boîte électrique associée à

l’interrupteur mural.

•

Le luminaire doit être mis à la terre. Si le l

de terre du lieu d’installation n’est pas présent,

ARRÊTER immédiatement l’installation et

consulter un électricien qualié.

Part #/Pieza #/Pièce #

Hardware Service Kit/Kit De Mantenimiento Del Equipo/Trousse De

Maintenance Quincaillerie

Finish/Finish/FiniModel/Modelo/Modèle

©2020 Hunter Fan Co.

ENGLISH

Twist or tape wire

ends together to make

it easier to thread

through downrod

Hunter Pro Tip:

NOTICE

In order to use a 12in rod by

itself you must rst remove

the post from the 6in rod and

install it on one of the ends of

the 12in rod.

Light Chandelier

Luz Lámpara tipo araña

Lumière Chandelier

J

L

K

A

B

G

H

C

D

F

I

M

E

N

O

P

19094

19095

Gablecrest

KC029-01-866

Painted Concrete/Cemento

Pintado/Béton Peint19094

ML009

r_102220

11.2 lbs (5.08 kg)

4

4

4

FINISHING THE INSTALLATION

CONNECTING THE WIRES

ASSEMBLING THE FIXTURE

PREPARING FOR INSTALLATION

CLEANING TIPS

Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light

and wipe down the xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.

Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old

xture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the

bag. One end of the threaded post (F) should be attached to the mounting bracket (A) with a washer and a hex nut (C,

D) in place. The other end should have the canopy loop (H) attached. Attach the mounting bracket (A) to the junction

box by securely tightening the mounting screws (B). Unscrew the canopy loop ring (I) from the canopy loop (H). Place

canopy (G) over the canopy loop (H) so that it’s ush with the ceiling. Adjust the position of the threaded post (F) on the

mounting bracket (A) so that the canopy (G) covers at least half of the exterior threads on the canopy loop (H) while it’s

securely connected to threaded post (F). Once the ideal position of the threaded post (F) is determined, tighten up the

washer (C) and the hex nut (D) onto the threaded post (F) just beneath the mounting bracket (A) to secure the threaded

post in place. Partially install grounding screw (E) into mounting bracket (A).

There are 4 12-inch rods (K), and 1 6-inch rod (L) included for each xture. Determine the correct number of rods

needed for proper hanging height. To lengthen the xture, add additional rods. To shorten the xture, trim the wires to

desired length. Leave at least 8 to 10 inches of wire in addition to the desired length and slide any excess rods off the

xture’s wiring to discard. Keep in mind that you must use at least one rod to hang the xture. Thread the wires through

the rods and pull the wires until taut before connecting the rods together. Place decorative cover (M) onto threaded

post (N) and screw rod onto threaded post (N) on the xture. Screw the threaded post of the top rod to canopy loop (I) of

canopy (F). Pull the xture wires through the top of the canopy.

Have a helper support the xture’s weight while completing the wiring. Attach the xtures wires to the power supply

wires from the junction box. Connect black to black (Live); white to white (grounded); grounding to grounding (green

or copper). Twist the ends of the wire pairs together. Then, twist on a

wire connector. Make sure all twists are in the same direction. Loop

xture’s ground wire around grounding screw (E) and tighten. If there

is no ground wire (green or copper) from the junction box, contact a

qualied electrician.

Place the canopy (G) ush to the ceiling and slide the canopy loop

ring (I) up beneath the canopy. Tightly screw canopy loop ring (I) onto

the canopy loop (H) to properly secure the canopy (G) in place. Slide

candle sleeves (O) onto sockets (P). Install light bulb (not included)

in accordance with the xture’s specications. Do not exceed the

recommended wattage. Your installation is now complete. Turn on the

power and test the xture.

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Hunter 19094 Gablecrest Lamp. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Hunter. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Hunter 19094 Gablecrest Lamp in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Hunter Lampen
Meer handleidingen voor Lampen

Beoordeling

Veelgestelde vragen over Hunter 19094 Gablecrest Lamp

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Hunter 19345 Van Nuys Lamp

Handleiding

Hunter 19780 Lochemeade Lamp

Handleiding

Hunter 19214 Bluff View Lamp

Handleiding

Hunter 19311 Belltown Lamp

Handleiding

Hunter 19332 Langwood Lamp

Handleiding

Hunter 19265 Felippe Lamp

Handleiding

Hunter 19330 Langwood Lamp

Handleiding

Hunter 19129 Astwood Lamp

Gerelateerde categorieën