Handleiding Hunter 19155 Devon Lamp

Handleiding

INSTALLATION INSTRUCTIONS

INSTRUCCIONES DE INSTALACIÓN/ INSTRUCTIONS D’INSTALLATION

For Models:

Para los Modelos:

Pour les Modèles:

Here are the

tools you’ll

need to

complete your

installation:

Estas son las

herramientas

que usted

necesitará para

completar su

instalación:

Voici les outils

dont vous

aurez besoin

pour réaliser

l’installation:

Ladder

Escalera

Échelle

Pliers

Alicates

Pince

Wire Strippers

Pelacables

Pince à dénuder

READ AND SAVE THESE INSTRUCTIONS

These instructions are provided for your safety. It

is very important that they are read carefully and

completely before beginning installation of the

lighting xture.

LEA Y GUARDE ESTAS INSTRUCCIONES

Estas instrucciones se proporcionan para su

seguridad. Es muy importante leerlas detenid-

amente y completamente antes de comenzar la

instalación de la lámpara.

LISEZ ET CONSERVEZ CES INSTRUCTIONS

Ces instructions sont fournies pour votre sécurité.

Il est très important de les lire attentivement dans

leur intégralité avant d’entreprendre l’installation

du luminaire.

Fixture weight ±2 lbs:

Peso ±2 lb:

Poids xe ±2 lbs:

•

WARNING

• All wiring must be in accordance with national

and local electrical codes ANSI/NFPA 70. If you

are unfamiliar with wiring or in doubt, consult a

qualied electrician.

• To avoid possible electrical shock, before

installing your light xture, disconnect the power

by turning off the circuit breakers to the outlet box

associated with the wall switch location.

• The lighting xture must be grounded. If the

ground wire for the installation site is not present,

immediately STOP installation and consult a

qualied electrician.

•

• Todo el cableado debe realizarse de acuerdo con

los códigos eléctricos locales y nacionales ANSI/

NFPA 70. Si no está familiarizado con el cableado,

o si tiene duda, consulte a un electricista calicado.

• Para evitar una posible descarga eléctrica, antes

de instalar su lámpara, desconecte la energía

apagando los interruptores automáticos (breakers)

que alimentan la caja de salida asociada con la

ubicación del interruptor de pared.

ADVERTENCIA

• L’appareil d’éclairage doit être mis à la terre.

Si le l de terre du lieu d’installation n’est pas

présent, ARRÊTEZ immédiatement l’installation et

consultez un électricien qualié.

•

AVERTISSEMENT

•

Tout le câblage doit être conforme aux codes

électriques nationaux et locaux en vigueur et à la

norme ANSI/NFPA70. Si vous n'avez pas l'habitude

de faire ce câblage ou en cas de doute, adressez-

vous à un électricien qualié.

• Pour éviter tout choc électrique, avant d’installer

le luminaire, coupez le courant en éteignant les

disjoncteurs de la boîte électrique associée à

l’interrupteur mural.

•

Le luminaire doit être mis à la terre. Si le l

de terre du lieu d’installation n’est pas présent,

ARRÊTER immédiatement l’installation et

consulter un électricien qualié.

©2021 Hunter Fan Co.

Light Linear Chandelier

Luz Lámpara Lineal

Lumière Chandelier Linéaire

Part #/Pieza #/Pièce #

Hardware Service Kit/Kit De Mantenimiento Del Equipo/Trousse De

Maintenance Quincaillerie

Glass/Domo De Vidrio/Verre

Part #/Pieza #/Pièce #

ENGLISH

Twist or tape wire

ends together to make

it easier to thread

through downrod

Hunter Pro Tip:

NOTICE

In order to use a 12in rod by

itself you must rst remove

the post from the 6in rod and

install it on one of the ends of

the 12in rod.

NOTICE

Drill 9/64" pilot holes in

support structure to aid in

securing light xture.

Drill

Taladro

Foret

Finish/Finish/FiniModel/Modelo/Modèle

Type/Tipo/TypeModel/Modelo/ Modèle

Screwdriver

Destornilladore

Tournevis

H

L

M

K

G

N

O

P

F

I

J

E

D

C

B

A

Q

19155

19156

Devon Park

KC03205000

KC03204000

Onyx Bengal/Bengala Ónix/

Onyx du Bengale

Brushed Nickel/Níquel Pulido/

Nickel Brossé

19155

19156

KA28401147

Clear Halophane Glass/

Vidrio Transparente Tipo

Holophane/

Verre Holophane Transparent

19155

19156

ML017

r_020921

14.1 lbs (6.39 kg)

3

3

3

FINISHING THE INSTALLATION

CONNECTING THE WIRES

PREPARING FOR INSTALLATION

CLEANING TIPS

Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light

and wipe down the xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.

Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old

xture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the

bag. Mounting plate (B) contains several pairs of threaded holes. Find the pair of holes that matches the spacing on

the holes on the xtures canopy. Attach two mounting screws (A) to the mounting plate (B). Tighten nuts (C) to hold the

screws in place. Put the hollow rubber plug (I) inside the hole in the ceiling, then insert the tapping screw (J) through

the mounting plate (B) into the rubber plug (I). Place the mounting plate (B) over the junction box so that mounting

screws (A) and nuts (C) are visible. Pull the house wires through the center of mounting plate (B). Secure mounting

plate (B) to the junction box by tightening the screws (D). Partially install grounding screw (E) into mounting plate (B).

Raise canopy (F) to mounting plate (B) and position mounting screws (A) so that they protrude through the openings of

canopy (F). Secure canopy (F) in place with decorative nuts (L). Adjust alignment before installing glass. Secure glass (P)

onto the socket (O) with screws (N). Install light bulb (not included) in accordance with the xture’s specications. Do

not exceed the recommended wattage. Your installation is now complete. Turn on the power and test the xture.

Slide cord (M) through cord grip (K) to adjust the wire to desirable length [set screw (H) may need to be loosened rst].

Tighten the set screw (H) with the included screwdriver (G) to lock it

tight. Tie a knot in each cord (M) above the canopy for strain relief [see

existing knot (Q) for example]. Cut excess cord leaving enough length

to reach from each end to center cord to assure that the connections of

each of the 3 cords and house wiring can be made. Remove the outer

jacket of each cord (M) to expose individual wires (white, black, green).

Strip half an inch of jacket away from the ends of each individual

wire. Have a helper support the xture’s weight while completing the

wiring. Attach the xture’s wires [from all 3 cords (M)] to the power

supply wires from the junction box. Connect black to black (Live); white

to white (grounded); grounding to grounding (green or copper). Twist

the ends of the wire pairs together. Then, twist on a wire connector.

Make sure all twists are in the same direction. Loop xture’s ground

wire around grounding screw (E) and tighten. If there is no ground wire (green or copper) from the junction box,

contact a qualied electrician.

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Hunter 19155 Devon Lamp. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Hunter. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Hunter 19155 Devon Lamp in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Hunter Lampen
Meer handleidingen voor Lampen

Veelgestelde vragen over Hunter 19155 Devon Lamp

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.