Handleiding Hunter 19728 Vidria Lamp

Handleiding

INSTALLATION INSTRUCTIONS

INSTRUCCIONES DE INSTALACIÓN/ INSTRUCTIONS D’INSTALLATION

For Models:

Para los Modelos:

Pour les Modèles:

Here are the

tools you’ll

need to

complete your

installation:

Estas son las

herramientas

que usted

necesitará para

completar su

instalación:

Voici les outils

dont vous

aurez besoin

pour réaliser

l’installation:

Ladder

Escalera

Échelle

Pliers

Alicates

Pince

Wire Strippers

Pelacables

Pince à dénuder

READ AND SAVE THESE INSTRUCTIONS

These instructions are provided for your safety. It

is very important that they are read carefully and

completely before beginning installation of the

lighting xture.

LEA Y GUARDE ESTAS INSTRUCCIONES

Estas instrucciones se proporcionan para su

seguridad. Es muy importante leerlas detenid-

amente y completamente antes de comenzar la

instalación de la lámpara.

LISEZ ET CONSERVEZ CES INSTRUCTIONS

Ces instructions sont fournies pour votre sécurité.

Il est très important de les lire attentivement dans

leur intégralité avant d’entreprendre l’installation

du luminaire.

Fixture weight ±2 lbs:

Peso ±2 lb:

Poids xe ±2 lbs:

•

WARNING

• All wiring must be in accordance with national

and local electrical codes ANSI/NFPA 70. If you

are unfamiliar with wiring or in doubt, consult a

qualied electrician.

• To avoid possible electrical shock, before

installing your light xture, disconnect the power

by turning off the circuit breakers to the outlet box

associated with the wall switch location.

• The lighting xture must be grounded. If the

ground wire for the installation site is not present,

immediately STOP installation and consult a

qualied electrician.

•

• Todo el cableado debe realizarse de acuerdo con

los códigos eléctricos locales y nacionales ANSI/

NFPA 70. Si no está familiarizado con el cableado,

o si tiene duda, consulte a un electricista calicado.

• Para evitar una posible descarga eléctrica, antes

de instalar su lámpara, desconecte la energía

apagando los interruptores automáticos (breakers)

que alimentan la caja de salida asociada con la

ubicación del interruptor de pared.

ADVERTENCIA

• L’appareil d’éclairage doit être mis à la terre.

Si le l de terre du lieu d’installation n’est pas

présent, ARRÊTEZ immédiatement l’installation et

consultez un électricien qualié.

•

AVERTISSEMENT

•

Tout le câblage doit être conforme aux codes

électriques nationaux et locaux en vigueur et à la

norme ANSI/NFPA70. Si vous n'avez pas l'habitude

de faire ce câblage ou en cas de doute, adressez-

vous à un électricien qualié.

• Pour éviter tout choc électrique, avant d’installer

le luminaire, coupez le courant en éteignant les

disjoncteurs de la boîte électrique associée à

l’interrupteur mural.

•

Le luminaire doit être mis à la terre. Si le l

de terre du lieu d’installation n’est pas présent,

ARRÊTER immédiatement l’installation et

consulter un électricien qualié.

©2021 Hunter Fan Co.

Light Cluster

Luz En Racimo

Lumière Grappe

Part #/Pieza #/Pièce #

Hardware Service Kit/Kit De Mantenimiento Del Equipo/Trousse De

Maintenance Quincaillerie

Glass/Domo De Vidrio/Verre

Part #/Pieza #/Pièce #

ENGLISH

Finish/Finish/FiniModel/Modelo/Modèle

Type/Tipo/TypeModel/Modelo/ Modèle

Screwdriver

Destornilladore

Tournevis

F

G

L

J

I

H

B

C

K

D

E

A

19727

19728

Vidria

KG20302214

KG20301119

Brushed Nickel/Níquel Pulido/

Nickel Brossé

Matte Black/Negro Mate/

Noir Mat

19727

19728

KG20501147

KG20502295

19727

19728

ML172

r_111121

10.1 lbs (4.58 kg)

3

3

3

FINISHING THE INSTALLATION

CONNECTING THE WIRES

PREPARING FOR INSTALLATION

CLEANING TIPS

Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light

and wipe down the xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.

Carefully remove all contents from the carton. Ensure bubble wrap is in place to protect glass during installation. Shut

off the power at the circuit breaker and completely remove the old xture from the ceiling, including the old mounting

bracket. Remove the new mounting bracket assembly from the bag. Then remove cap nuts (L) from mounting screws

(C). Place the mounting plate (B) over the junction box so that mounting screws (C) and nuts (A) extend out away from

the ceiling. Depending on the placement of your junction box the position of mounting screws (C) may need to be

adjusted to allow the canopy to be ush with the ceiling. Adjust the position of mounting screws (C) so that mounting

screws (C) can be exposed 5-6 mm after passing through the canopy (K) to properly t the cap nuts. Mounting screws

(C) can be adjusted by loosening nuts (A) and loosening or tightening mounting screws (C). Once the ideal position of

mounting screws (C) has been conrmed, tighten nuts (A) on mounting screws (C) on the front of the mounting plate

to ensure that mounting screws (C) are secure. Pull the house wires through the center of mounting plate (B). Secure

mounting plate (B) to the junction box by tightening the screws (D). By measuring, determine the correct cord length

for proper hanging height.

Loosen the screw (F) with a screwdriver (E), adjust the wire to the

proper length, and then lock the screw (F) with a screwdriver (E) to

lock the wire tight. Adjust the placement of the strain relief (R) on

the cord above the canopy. Cut excess cord leaving enough length to

reach from each edge to the center of the canopy to assure that the

connections of each of the 3 cords and house wiring can be made.

Remove the outer jacket of each cord to expose individual wires

(white, black, green). Strip half an inch of jacket away from the ends of

each individual wire. Have a helper support the xture’s weight while

completing the wiring. Tighten the screw collar loop (I) into mounting

plate (B). Attach the xture’s wires [from all 3 cords] to the power

supply wires from the junction box. Connect black to black (Live); white to white (grounded); grounding to grounding

(green or copper). Twist the ends of the wire pairs together. Then, twist on a wire connector. Make sure all twists are

in the same direction. Loop xture’s ground wire around grounding screw (H) and tighten. If there is no ground wire

(green or copper) from the junction box, contact a qualied electrician.

Raise canopy (K) to mounting plate (B) and position mounting screws (C) so that they protrude through the openings of

canopy (K). Secure canopy (K) in place with cap nuts (L). Carefully remove all bubble wrap from sockets and glass. Install

light bulb (not included) in accordance with the xture’s specications. Do not exceed the recommended wattage. Your

installation is now complete. Turn on the power and test the xture.

Clear Glass/Vidrio Transparente/

Verre Transparent

Smoked Glass/Vidrio Ahumado/

Verre Fumé

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Hunter 19728 Vidria Lamp. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Hunter. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Hunter 19728 Vidria Lamp in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Hunter Lampen
Meer handleidingen voor Lampen

Beoordeling

Veelgestelde vragen over Hunter 19728 Vidria Lamp

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Hunter 19714 Lochemeade Lamp

Handleiding

Hunter 19775 Lochemeade Lamp

Handleiding

Hunter 19085 Squire Manor Lamp

Handleiding

Hunter 19338 Langwood Lamp

Handleiding

Hunter 19289 Highland Hill Lamp

Handleiding

Hunter 19137 Astwood Lamp

Handleiding

Hunter 19368 Indria Lamp

Handleiding

Hunter 19161 Hartland Lamp

Gerelateerde categorieën