Handleiding Kichler 10784OZLED Lamp

Handleiding

WARNING:

• This fixture is intended for installation in accordance with the

National Electric Code (NEC) and all local code specifications.

• Supply wires are not intended for use through or concealed

behind walls, floors, or ceilings.

DIMMING: This LED fixture is compatible with electronic low

voltage dimmers only.

CAUTION – RISK OF SHOCK – Disconnect Power at the main

circuit breaker panel or main fuse box before starting and during

the installation.

Determine size of outlet box. Measure distance between threaded

holes of outlet box. If measurement is 3-1/2” or 2-3/4” follow

instructions below. If measurement is 3-1/4”, please see instruc-

tions for mounting to 3-1/4” hole distance outlet box.

Instructions for mounting to 3-1/2” hole distance and 2-3/4” hole

distance outlet box.

1) Read and understand all instructions and illustrations com-

pletely before proceeding with assembly and installation of

fixture.

2) If you have any doubts about how to install this fixture, or if

the fixture fails to operate completely, please contact a

qualified electrician.

3) All parts must be used as indicated in the instructions. Do

not substitute any parts, leave parts out, or use any parts

that are worn or broken. Failure to obey this instruction

could invalidate the UL listing, C.S.A. certification, and/or

ETL listing of this fixture.

4) Fixture is to be connected to a single branch circuit.

5) Mounting surface should be clean, dry, flat and 1/4” larger

than the fixture housing surface.

6) Install (2) strap mounting screws into outlet box leaving

small amount of threads exposed.

7) Grounding instructions: (See Illus. A or B).

A) On fixtures where mounting strap is provided with a hole

and two raise dimples. Wrap ground wire from outlet box

around green ground screw, and thread into hole.

B) On fixtures where a cupped washer is provided. Put ground

wire from outlet box under cupped washer and green

ground screw and thread screw into hole in mounting strap.

If fixture is provided with ground wire. Connect fixture ground

wire to outlet box ground wire with wire connector, (not provided)

after following the above steps. Never connect ground wire to

black or white power supply wires.

8) Make wire connections. Reference chart below for correct

connections and wire accordingly.

9) Carefully push wire connections into outlet box making

sure all connections remain secure.

10) Push fixture to ceiling, align the larger hole side of keyhole

slot with screws in outlet box. Push fixture to ceiling and

turn fixture in direction of smaller side of keyhole slots until

it stops. Tighten strap mounting screws to secure.

11) Raise the diffuser up to the fixture. Fit the edge of diffuser

inside the lip of back plate. The threaded studs on back plate

should be on the outside of the diffuser.

12) Place reinforcement ring over diffuser. Align holes in ring with

ends of studs.

13) Screw lock-up knobs onto threaded studs. Tighten knobs to

secure ring and diffuser in place.

GREEN GROUND

SCREW

CUPPED

WASHER

OUTLET BOX

GROUND

FIXTURE

GROUND

DIMPLES

WIRE CONNECTOR

OUTLET BOX

GROUND

GREEN GROUND

SCREW

FIXTURE

GROUND

A

B

Connect Black or

Red Supply Wire to:

Connect

White Supply Wire to:

Black White

*Parallel cord (round & smooth) *Parallel cord (square & ridged)

Clear, Brown, Gold or Black

without tracer

Clear, Brown, Gold or Black

with tracer

Insulated wire (other than green)

with copper conductor

Insulated wire (other than green)

with silver conductor

*Note: When parallel wires (SPT I & SPT II)

are used. The neutral wire is square shaped

or ridged and the other wire will be round in

shape or smooth (see illus.)

Neutral Wire

Date Issued: 12/30/16 IS-10784LED-US

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

Instructions for mounting onto a 3-1/4” (hole distance) outlet box

using provided mounting strap:

1) Follow steps 1-5 from 3-1/2” and 2-3/4” instructions.

2) Starting from outlet box side of mounting strap, thread (2)

longer mounting screws into threaded holes spaced 2-3/4”

apart. Tighten to secure.

3) Raise mounting strap to outlet box. Longer screws should be

pointing downward.

4) Align slots in mounting strap to threaded holes in outlet box.

Thread (2) strap mounting screws into outlet box. Center

strap in outlet box. Tighten screws to secure.

5) Continue with steps 7-9 from 3-1/2” and 2-3/4” instructions.

6) Push fixture to ceiling, align the larger hole side of keyhole

slots with screws in mounting strap. Push fixture to ceiling

and turn fixture in direction of smaller side of keyhole slots

until it stops. Pass (2) lockwashers and thread (2) nuts on

mounting screws. Tighten to secure.

7) Continue with steps 11-13 from 3-1/2” and 2-3/4” instructions.

SEE OTHER SIDE FOR SPANISH TRANSLATIONS.

VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause unde-

sired operation.

Note: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable pro-

tection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to ra-

dio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

10784/10786LED

REINFORCEMENT RING

LOCK-UP KNOB(S)

DIFFUSER

THREADED STUD(S)

BACK PLATE

WIRE

CONNECTOR(S)

OUTLET BOX

REINFORCEMENT RING

LOCK-UP KNOB(S)

DIFFUSER

THREADED STUD(S)

BACK PLATE

WIRE

CONNECTOR(S)

OUTLET BOX

FOR INSTALLATION ON

3" OUTLET BOX

MOUNTING SCREW(S)

MOUNTING STRAP

NUT(S)

STRAP MOUNTING SCREW(S)

STRAP MOUNTING SCREW(S)

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Kichler 10784OZLED Lamp. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Kichler. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Kichler 10784OZLED Lamp in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Kichler Lampen
Meer handleidingen voor Lampen

Veelgestelde vragen over Kichler 10784OZLED Lamp

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Beoordeling

Gerelateerde producten

Handleiding

Kichler 15410AZT Lamp

Handleiding

Kichler 10438NCHLED Lamp

Handleiding

Kichler 15072AZT Lamp

Handleiding

Kichler 15079BKT Lamp

Handleiding

Kichler 11319NILED Lamp

Handleiding

Kichler 15231AZT Lamp

Handleiding

Kichler 10790NILED Lamp

Handleiding

Kichler 10784NILED Lamp

Gerelateerde categorieën