Handleiding Kichler 15CS75SS Contractor Lamp

Handleiding

For warranty information please visit: http://www.landscapelighting.com/portal/warranty_page

Para informacion de la garantia por favor visite: www.landscapelighting.com/portal/warranty_page

Date Issued: 10/31/17

IS-15CS75-US

This instruction sheet covers the installation of the following Kichler

®

Transformers: 15CS75SS. Read these instructions carefully before installing

this unit.

• This power supply is for use with landscape lighting systems only.

• Do not submerge transformer.

• This device is accepted as a component of a landscape lighting system

where the suitability of the combination shall be determined by National

Electric Code or local authorities having jurisdiction.

• WARNING: Risk of electric shock, use only with low voltage landscape

fixtures and accessories. DO not use with swimming pool or spa lighting

fixtures.

• Do not connect two or more power supplies in parallel.

• Suitable for indoor or outdoor use.

• For use in dwellings only with provided conduit adapter plate.

• National Electrical Code requires that wiring where concealed or

extended through a building wall must be enclosed in conduit.

• Transformer should be mounted close to power source. Extension cords

should not be used with this unit.

• WARNING: (for Power Supply Cord connected POWER UNIT)

RISK OF ELECTRIC SHOCK. Install power unit 5 feet (1.5m) or more

from the pool, spa, or fountain where the power unit is installed (a)

indoor within 10 feet (3.0m) of a pool, spa, or fountain, or (b) outdoor,

connect power to unit to a receptacle protected by a GFCI.

• This outdoor power unit shall be connected to a 115/120 volt covered

GFCI receptacle marked “Wet Location” while in use.

• Mount the rain-tight transformer at least one foot above ground level with

the wire terminals facing down. NOTE: Do not energize transformer until

installation of system is complete.

• Direct burial rated wire is to be buried a minimum of 6” (152mm) beneath

the surface of the ground.

NOTE: If additional Direct Burial wire is needed, contact your local

Kichler

®

landscape distributor.

• 8 GA wire can be purchased in length of 250’ (76 M), 15503-BK.

• 10 GA wire can be purchased in length of 250’ (76 M), 15504-BK.

• 12 GA wire can be purchased in lengths of 100’ (30 M), 15501-BK;

250’ (76 M), 15502-BK; 500’ (152M), 15505-BK; and 1000’ (304 M),

15506-BK.

• Finding Transformer Load: Low voltage systems require the use of a

transformer to reduce standard 120-VOLT power from your home to

12-VOLTS. To determine the transformer size you will need, add up the

wattages of all lamps you plan to use. Select a transformer that matches

as closely as possible to the total lamp wattage. For example, if you

have 11 fixtures all rated at 24.4 watts, you will need a 300 watt

(VA) transformer (11 x 24.4 = 268.4 watts). Generally, the total lamp load

should not be less than one-third the transformers wattage rating, nor

exceed its maximum wattage capacity. If your total wattage is too high,

either divide the load between two transformers, or use a more powerful

transformer.

INSTALLATION INSTRUCTIONS

1) Determine desired location for mounting transformer. NOTE: When

deciding location for mounting consideration should be taken for the

requirements listed above.

2) Mark position of top portion of the keyhole slot location at top of

transformer and the slot located at bottom.

3) If mounting to a solid surface such as wood, siding, etc;

A) Drill 1/8” diameter pilot holes at positions marked in Step 2.

B) Drive screws approximately half way into holes.

If mounting to drywall:

A) Drill 1/4” diameter holes at positions marked in Step 2.

B) Push plastic anchors into holes and tap until flush.

C) Drive screws approximately half-way into plastic anchors.

4) Slip large portion of keyhole over head of top screw and allow transformer

to slide down, making sure bottom slot is behind head of bottom screw.

5) Tighten screws until transformer is secure.

6) Split 12/2. 10/2, or 8/2 cable approximately 3”, and strip 1/2” insulation

off each wire. 12/2. 10/2, and 8/2 cable is the heavy black cable which

all Kichler

®

12-volt low voltage lighting fixtures will be connected.

(Reference above for description and part numbers).

7) On the bottom of the terminal block push one bare wire into the hole

marked “COM” and tighten the corresponding screw on terminal block

face until wire is secure. See chart for terminal screw torque specification.

See chart for maximum wire sizes and counts.

Wire Sizes Max. no. of conductors

Tightening Torque

#12 8 3.6-4.0 N-m (32-35 lb-in)

#10 4 3.6-4.0 N-m (32-35 lb-in)

#8 1 4.1-4.5 N-m (36-40 lb-in)

8) Determine the appropriate voltage tap (holes marked 12V or 15V) for

remaining bare wire.

• For optimum light output, the voltage at the lamp socket should

range between 10.8 and 12 volts (incandescent).

• For optimum light output, the voltage at the lamp socket should

range between 12 to 15 volts (LED).

For more information on voltage drop, consult the Kichler Landscape

Lighting Catalog or contact your local Kichler distributor.

9) Push remaining bare wire into the appropriate hole on bottom of

terminal block and tighten the corresponding screw on terminal block

face until wire is secure. Again, refer to torque specifications in chart.

10) TIMER INSTRUCTIONS ARE LOCATED ON INSIDE OF

TRANSFORMER COVER.

11) Optional Photo Control Installations:

A) Make sure power is off and transformer is NOT plugged into

an electrical outlet. NOTE: No splice is required, transformer is

equipped with jumper connector.

B) Open front cover of the transformer case by lifting the cover

up. Locate and disconnect the white jumper connector inside

the housing. *Save the jumper connector with these instructions

for possible future use.

C) Remove one (1) of the 7/8” diameter knockouts on the side of

the transformer and push the photo control white connector

through the knockout hole. Inside the housing, slide the spacer

and star nut over the white connector and thread it on to the

photo control and tighten.

D) Plug photo control white connector into the housing connector.

Insure that the side latch locks the connectors.

E) Locate transformer and position photo control so that no light

will shine on the cell. It will cause the photo control to cycle on

and off. *In the unlikely event that the photo control should fail,

the lighting fixtures will remain on, even in the daytime. If this

should happen, follow these instructions and remove the defective

photo control and place the jumper connector in its place.

12) Plug power supply cord into standard 115/120 volt receptacle. NOTE:

The power supply cord must be plugged into a weather tight receptacle

equipped with a Ground Fault Interrupter (GFCI).

CIRCUIT BREAKER

(SECONDARY SIDE - 12 VOLT SIDE)

• Circuit breaker will trip if there is a short or if total

wattage installed exceeds rated wattage per circuit.

• To reset breaker, flip switch to ‘OFF’ then back to

‘ON’ position.

• If the unit cycles on and off without regard to the

timer setting, it should be checked by a qualified

service person.

THERMAL PROTECTION

(PRIMARY SIDE - 120 VOLT SIDE)

• This unit is equipped with a thermal protector and

will shut off if overheated.

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Kichler 15CS75SS Contractor Lamp. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Kichler. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Kichler 15CS75SS Contractor Lamp in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Kichler Lampen
Meer handleidingen voor Lampen

Beoordeling

Veelgestelde vragen over Kichler 15CS75SS Contractor Lamp

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Kichler 16019CBR30 VLO Lamp

Handleiding

Kichler 15694AZ Rock Lamp

Handleiding

Kichler 15450TZT Mica Lamp

Handleiding

Kichler 15556WH Transformer Lamp

Handleiding

Kichler 11251BKT30 Cylinder Lamp

Handleiding

Kichler 15805BKT30R Shallow Lamp

Handleiding

Kichler 15601AZT Surface Lamp

Handleiding

Kichler 16016WHT30 VLO Lamp

Gerelateerde categorieën