Handleiding McCulloch EB356a Kettingzaag

Handleiding

8 9

TO INSTALL SAW CHAIN:

WARNING

Always wear heavy duty gloves when handling saw chain

or making sa

w chain adjustments.

1. Spread chain out in a loop with cutting edges (A)

pointing CLOCKWISE around loop (Figure 3-3F).

2. Slip the chain around the sprocket (B) behind the

clutch (C). Make sure the links fit between the sprock-

et teeth (Figure 3-3G).

3. Guide the drive links into the groove (D) and around

the end of the bar (Figure 3-3G).

NOTE: The saw chain may droop slightly on the lower part

of bar. This is normal.

4. Pull guide bar forward until chain is snug. Ensure all

drive links are in the bar groove.

5. Install the clutch cover making sure the tang is posi-

tioned in the lower hole in the guide bar. Make sure

the chain does not slip off of the bar. Install the bar

retaining nuts hand tight and follow tension adjust-

ment instructions in Section 3-4.

NOTE: The guide bar retaining nuts are installed only hand

tight at this point because saw chain adjustment is

required. Follow instructions in Section 3-4, Saw Chain

Tension Adjustment.

3-4. SAW CHAIN TENSION ADJUSTMENT

Proper tension of saw chain is extremely important and

must be checked before starting, as well as during any cut-

ting operation.

Taking the time to make needed adjustments to the saw

chain will result in improved cutting performance and pro-

longed chain life.

WARNING

Always wear heavy duty gloves when handling saw chain

or making saw chain adjustments.

TO ADJUST SAW CHAIN:

1. Hold nose of guide bar up and turn adjustment screw

(D) CLOCKWISE to increase chain tension. Turning

screw COUNTERCLOCKWISE will decrease amount

of tension on chain. Ensure the chain fits snugly all the

way around the guide bar (Figure 3-4A).

2. After making adjustment, and while still holding nose

of bar in the uppermost position, tighten the bar

retaining nuts securely. Chain has proper tension

when it has a snug fit all around and can be pulled

around by gloved hand.

NOTE: If chain is difficult to rotate on guide bar or if it binds,

too much tension has been applied. This requires minor

adjustment as follows:

A. Loosen the bar retaining nuts so it is finger tight.

Decrease tension by turning the bar adjustment screw

COUNTERCLOCKWISE slowly. Move chain back and

forth on bar. Continue to adjust until chain rotates

freely, but fits snugly. Increase tension by turning bar

adjustment screw CLOCKWISE.

B. When saw chain has proper tension, hold nose of bar

in uppermost position and tighten the bar retaining nut

securely.

3 - ASSEMBLY INSTRUCTIONS

CAUTION

A ne

w saw chain stretches, requiring adjustment after as

few as 5 cuts. This is normal with a new chain, and the

interval between future adjustments will lengthen quickly.

CAUTION

If saw chain is TOO LOOSE or TOO TIGHT, the sprocket,

bar, chain, and crankshaft bearings will wear more rapidly.

Study Figure 3-4B for information concerning correct cold

tension (A), correct warm tension (B), and as a guide for

when saw chain needs adjustment (C).

3-5. CHAIN BRAKE

®

MECHANICAL TEST

Your chain saw is equipped with a CHAIN BRAKE

®

that

reduces possibility of injury due to kickback. The brake is

activated if pressure is applied against brake lever when,

as in the event of kickback, operator’s hand strikes the

lever. When the brake is actuated, chain movement stops

abruptly.

WARNING

The purpose of the CHAIN BRAKE

®

is to reduce the possi-

bility of injury due to kickback; however, it cannot provide

the intended measure of protection if the sa

w is oper

ated

carelessly.

Alw

a

ys test the CHAIN BRAKE

®

bef

ore using y

our sa

w and

per

iodically while on the job

.

To Test CHAIN BRAKE

®

:

1.

The CHAIN BRAKE

®

is DISENGA

GED (chain can

move) when BRAKE LEVER IS PULLED BACK AND

LOCKED. Be sure the chain bareak latch is in the on

position. (Figure 3-5A).

2. The CHAIN BRAKE

®

is ENGAGED (chain is stopped)

when brake lever is in forward position and the chain

break latch is in the off position. You should not be

able to move chain (Figure 3-5B).

NOTE: The brake lever should snap into both positions. If

strong resistance is felt, or lever does not move into either

position, do not use your saw. Take it immediately to an

Authorized Service Center for repair.

3 - ASSEMBLY INSTRUCTIONS

3-3F

3-3G

A

D

B

C

3-4A

D

3-4B

3-5A

3-5B

ON

A

C

B

OFF

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je McCulloch EB356a Kettingzaag. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met McCulloch. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van McCulloch EB356a Kettingzaag in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor McCulloch Kettingzagen
Meer handleidingen voor Kettingzagen

Veelgestelde vragen over McCulloch EB356a Kettingzaag

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Beoordeling

Gerelateerde producten

Handleiding

McCulloch MXC1640DK Kettingzaag

Handleiding

McCulloch CSE 2040S Kettingzaag

Handleiding

McCulloch M4218 Kettingzaag

Handleiding

McCulloch CS 360T Kettingzaag

Handleiding

McCulloch Mac 540E Kettingzaag

Handleiding

McCulloch MCC3516F Kettingzaag

Handleiding

McCulloch CS 410 Elite Kettingzaag

Handleiding

McCulloch MXC1640D Kettingzaag

Gerelateerde categorieën