Home > Fietsen & Brommers > Fietslampen > NiteRider Fietslampen > NiteRider Pro 3600 Fietslamp

Handleiding NiteRider Pro 3600 Fietslamp

Handleiding voor je NiteRider Pro 3600 Fietslamp nodig? Hieronder kun je de handleiding gratis bekijken en downloaden als PDF in het Nederlands en/of Engels. Dit product heeft 0 veelgestelde vragen, 0 comments en heeft 0 stemmen. Is dit niet de handleiding die je zoekt, neem dan contact met ons op.

Is je product kapot en biedt de handleiding geen oplossing meer? Dan kun je voor reparatie gratis terecht bij Repair Café.

Handleiding

MOUNTING THE HEADLAMP

The Pro Series headlamp can be mounted to the handlebar or a helmet.

Universal Handlebar Mount

The Universal Handlebar Mount (UHM) is

designed to t on virtually any handlebar.

Included with the mount is a 2.5 mm Allen

wrench for adjusting the mount.

1. Turn the knob counter-clockwise, allowing the

hinge to swing open.

2. Place the mount on the handlebar on the left side the stem,

orienting the rectangular notch in

the slider clip to the rear.

3. Swing the hinge down to make

contact with the handlebar.

4. Swing the hex bolt up, seating the

knob into its recess.

5. Turn the knob clockwise to

tighten and secure the UHM to

the handlebar.

The UHM can be adjusted to accommodate any handlebar angle.

By loosening the 2.5 x 30 mm Allen screw, you can move the swing

arm back and forth to straighten the headlamp. Tighten the 2.5 x 30

mm screw after the adjustment.

To pivot the headlamp, loosen the 2.5 x 12 mm screw

located under the slider clip and swing arm and rotate

the headlamp to the desired position. Make this

adjustment before tightening the 2.5 x 30 mm screw.

Helmet Mount

1. Unclamp the straps on each side of the helmet mount and

pull them free.

2. Position the plastic mounting plate as close to the centerline

of the helmet as possible, orienting the parallel grooves on the

slider clip to the rear.

3. Feed each strap into and out of two helmet vents, circling

each strap back to the upper edge of the corresponding clamp.

4. Fasten the straps by inserting them into the clamps.

Inserting the Headlamp into the Handlebar or Helmet Mount

Insert the headlamp into the handlebar or helmet mount slider clip

from the rear forward. Gently rocking the lamp as you slide it may

help. Do not push the release lever when

inserting the headlamp into the slider clip;

let the lamp snap into place by itself.

To remove the headlamp, push the release

lever forward and slide the lamp backward.

Note: After mounting the headlamp, adjust it so the beam illuminates

the road properly without distracting oncoming riders.

Release

Lever

MOUNTING THE BATTERY SYSTEM

The “battery system” consists of a tray, which mounts to the bike frame,

and a Li-Ion battery that releases quickly from the tray for charging. The

battery system can also be placed in a jersey pocket, hydration pack or

fanny pack when helmet mounting the headlamp.

Warning: For safety reasons, a cyclist should never be tethered to the

bike. If the headlamp is mounted to the helmet, do not mount the bat-

tery system to the frame. Conversely, if the headlamp is mounted to the

handlebar, do not place the battery system in a pocket or pack.

Frame Mount

1. Thread the Velcro straps through the 2 slots on the bottom of

the battery tray.

2. Attach the concave surface of the tray to a safe, convenient

location on the frame (typically under the top or down tube),

placing the Velcro strap over the tube, but under any shift or

brake cables. The cable from the tray should extend toward the stem.

3. Secure the headlamp and battery tray cables to the frame

using the thin Velcro strapettes. Make sure the cables do not

interfere with any moving parts.

4. Aligning the arrow on the bottom of the battery with the red

arrow inside the tray, slide the battery into the tray until you

hear a noticeable click.

Note: If a click is not heard when sliding the battery into the tray, proper

mating did not occur. Remove battery from tray and repeat the process.

OPERATION

LED Indicators

The four LED indicators on top of

the headlamp, in front of the power

button, have multiple uses - as fuel

gauge steps and as identiers when in

the Program Select Mode.

Velcro Straps

Battery Tray

(Top View)

Battery Tray

(Bottom View)

Battery

(Bottom View)

Fuel Gauge

The 8-step, LED fuel gauge is located on top of the headlamp in

front of the power button. When all four LED’s are lit solid green, the

battery is fully charged. As the battery discharges ⅛ increments of

capacity, the LED’s, from right to left, successively go from solid to

blinking green, to out.

With only the nal ⅛ capacity remaining one LED blinks red. At this

time, the headlamp should be turned off and the battery recharged.

Power Button Uses

The power button, located on the top of the headlamp, is used to

turn the light on, change light and ash levels, turn the light off and

access the Program Select mode.

• Light On

- Press and release the power button to turn the light on.

- Cycle through the brightness levels by pressing and releasing

the power button.

• Flash

- To access ash mode press and hold the power button for

greater than 3 seconds.

- Cycle through the ash patterns by pressing and releasing the

power button.

• Light Off

- To turn the light off while in either normal light or ash mode,

press and hold the power button for greater than 1 and less

than 3 seconds.

• Program Mode

- From the “Off” position, press and hold the power button for 6

seconds to enter the ProgramSelect Mode.

DISCOVER THE NIGHT!

Thank you for choosing the Pro 3600 from NiteRider, the

innovator in technical lighting systems. The Pro 3600 consists

of dual beams of LED light and incorporates the latest in hardware

and software technology.

To get the most from your NiteRider light, we urge you to familiarize

yourself with the following safety and operating instructions. To learn

about the features of the D.I.Y. Software please refer to a separate,

companion document entitled, DIY Pro LED Series Software Guide.

PARTS LIST AND IDENTIFICATION

Parts for Pro 3600 System:

A. Dual Beam Headlamp

B. Li-Ion Battery (8 Cell, 7.4v, 11.6A Hr)

C. Universal Handlebar Mount (UHM)

D. Helmet Mount

E. Docking Station

F. AC Adapter

G. 36” Extension Cord

H. USB Cable

I. Battery Tray

Pocket or Pack

1. Route the headlamp 36” extension cable through a helmet vent or

along the outside of the helmet using the thin velcro strapette

secure the cable.

2. Connect the 36” extension cable to the battery, making sure the

cable does not interfere with any moving parts.

3. Simply place the battery in a pocket or pack.

Program Select Mode

There are a total of 5 Programs to select from. The Pro 3600 headlamp

has factory settings which are locked and cannot be modied. In

addition, the headlamp has memory to store four (4) additional operating

Programs which you create, modify and download to the Pro 3600

headlamp using the Docking Station.

D.I.Y. Software.

1. From the “O” position, press and hold the power button for 6

seconds to enter the Program Select Mode. The number of lit

LED’s will identify the Program currently being used.

- One LED lit red indicates the factory setting Program.

- One LED lit green indicates Program-1.

- The second LED from the left lit green indicates Program-2.

- The third LED from the left lit green indicates Program-3.

- All four LED’s lit green indicates Program-4.

2. Cycle through the (5) Programs by pressing and releasing the

power button.

3. To select a Program, press and hold the power button until all

lit LED’s begin to blink rapidly 5 times.

Once a Program has been selected, the light will operate under that

Program specications. Before shipping, NiteRider has initialized the

memory for the 4 additional operating Programs with factory settings.

Beoordeling

Laat ons weten wat je van de NiteRider Pro 3600 Fietslamp vindt door een beoordeling achter te laten. Wil je je ervaringen met dit product delen of een vraag stellen? Laat dan een bericht achter onderaan de pagina.

Bent u tevreden over de NiteRider Pro 3600 Fietslamp?
Ja Nee

Beoordeel dit product als eerste

0 stemmen

Praat mee over dit product

Laat hier weten wat jij vindt van de NiteRider Pro 3600 Fietslamp. Als je een vraag hebt, lees dan eerst zorgvuldig de handleiding door. Een handleiding aanvragen kan via ons contactformulier.

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je NiteRider Pro 3600 Fietslamp. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met NiteRider. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van NiteRider Pro 3600 Fietslamp in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.