Handleiding Ozito CMX-125U Cementmixer

Handleiding

For best loading results, proceed as follows:

• Add the required amount of stone into the drum.

• Add the required amount of sand into the drum.

• Add the required amount of cement into the drum.

• Pour the required amount of water into the drum.

Note: When measuring out cement and ballast (or sharp sand/gravel),

use a small bucket to ensure accurate ratios of cement: ballast. Refer

to the instructions that come with your cement.

Ensure your chosen quantity of concrete is large enough that the

cement mixer will function and small enough that it will t in the

drum, see load sizes in specications section of manual to calculate

quantities.

• When the mixture is the right consistency to use, empty the drum.

Pour the mixed cement by releasing the tipping handle and rotating

the drum to the empty position while the machine is running. Be sure

to pour the mix slowly and smoothly to avoid tilting the cement mixer.

• When the drum is empty, turn the cement mixer off.

CEMENT

MIXER

550W 125L

SPECIFICATIONS

Motor: 550W

No Load Speed 2950/min

Drum Speed: 34/min

Gross Drum Volume: 125L (4.41 cu ft)

Unmixed Dry Volume: 100L (3.53 cu ft)

Mixed Wet Volume: 91L (3.21 cu ft)

Drum Mouth: Ø375mm (14 ¾”)

IP Rating: IP44

Weight: 48kg

CMX-125U

WHAT’S IN THE BOX

Cement Mixer

Assembly Fasteners

DESCRIPTION OF SYMBOLSTROUBLESHOOTING

• Never put any of your body parts (including hands) inside the drum while it is

rotating.

• Wipe off any external material on the motor cover. Do not use petrol,

turpentine, lacquer, paint thinner, dry cleaning uids or similar products.

• The use of chemical products or solvents may damage the motor cover.

• Thoroughly clean your cement mixer at the end of each days operation.

• Keep your cement mixer clean. The slightest trace of material left in the drum

assembly will harden and attract more material each time the machine is used.

• Dried cement should be scraped out of the drum assembly.

• DO NOT throw bricks into the drum assembly to clean it out.

• DO NOT beat on the drum with a shovel, hammer or other tools to break up

accumulation of dried cement mix as the cement mixer may be damaged.

• The drum may be scoured for approximately 2 minutes, using a 1” stone and

water mixture. After this, discharge the stone/water mixture and hose down the

drum assembly inside and out.

• The IP44 protection clad construction of the mixer enables the DRUM

ASSEMBLY ONLY to be hosed down safely. Avoid getting water on the motor

and motor housing, DO NOT wet the motor and motor housing.

General Maintenance

• Ball bearings are packed with grease at the factory. No further lubrication of

bearings is required.

• During normal use, painted surfaces can lose their coating during the mixing

process. Wipe all exposed surfaces regularly with an oily rag to prevent

corrosion. (Note: Loss of paint and rust are not covered under warranty.)

• Keep air vents clean of dust and dirt.

• Remove dust and dirt from the cement mixer regularly with soft cloth, brush or

compressed air. Use a mild detergent and a soft cloth to clean plastic parts.

• If the power cord is damaged, have it replaced by an electrician or a power tool

repairer.

• Regularly check that all bolts, screws and nuts are securely xed as these

could work loose during normal operation.

• Do not open the motor cover under any circumstances.

WARRANTY

SPARE PARTS

WARNING! For your own safety, do not try to use your cement mixer or

plug it in until it is completely assembled and installed according to the

instructions and until you have read and understood the following:

This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning use of the appliance by a

person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

• Avoid dangerous conditions. Do not use the mixer in wet or damp areas

or expose it to rain. Do not use it in areas where fumes from paint, solvents or

ammable liquids pose a potential hazard.

• Inspect your cement mixer. Check your cement mixer before turning it on. Keep

guards in place and in working order. Form a habit of checking to see that keys and

adjusting wrenches are removed from the cement mixer area before turning on.

Replace damaged, missing or failed parts before using it.

• Wear protective gear. Foreign objects may be thrown from the cement mixer while

in operation. This can cause facial injuries. Always wear safety goggles and/or face

shields.

• Loading the cement mixer. Do not attempt to load or unload the contents until the

cement mixer has stopped. Keep hands out of the way of all moving parts.

• Never leave cement mixer running unattended. Don’t leave cement mixer until it

has come to a complete stop.

• Disconnect power. Unplug when not in use, before making adjustments, changing

parts, cleaning, or working on the mixer.

• Maintain your cement mixer with care. Clean the cement mixer immediately after

use. Keep the cement mixer clean for best and safest performance.

• Moving the cement mixer. Do not tow the cement mixer by using a vehicle. Use

an approved trailer to move the cement mixer if it is to be transported.

• Drugs, alcohol and medication. Do not operate the mixer while under the

inuence of drugs, alcohol, or any medication that could affect your ability to use it

properly.

CEMENT MIXER SAFETY WARNINGS

GENERAL POWER TOOL SAFETY WARNINGS

ELECTRICAL SAFETY

0616

OPERATION

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and

instructions may result in electric shock, re and/or serious injury.

Save all warnings and instructions for future reference. The term “power tool” in the warnings refers

to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b. Donotoperatepowertoolsinexplosiveatmospheres,suchasinthepresenceofammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c. Keep children and bystanders away while operating a power tool. Distractions can cause you to

lose control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching outlets will

reduce risk of electric shock.

b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the

risk of electric shock.

d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase

the risk of electric shock.

e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

f. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do

notuseapowertoolwhileyouaretiredorundertheinuenceofdrugs,alcoholormedication. A

moment of inattention while operating power tools may result in serious personal injury.

b. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce

personal injuries.

c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to

power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your

nger on the switch or energising power tools that have the switch on invites accidents.

d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

g. If devices are provided for the connection of dust extraction and collection facilities, ensure

these are connected and properly used. Use of dust collection can reduce dust-related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the correct power tool for your application. The correct power tool

will do the job better and safer at the rate for which it was designed.

b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or the battery pack from the power tool before

making any adjustments, changing accessories, or storing power tools. Such preventive safety

measures reduce the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the

power tool or these instructions to operate the power tool. Power tools are dangerous in the hands

of untrained users.

e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and

any other condition that may affect the power tool’s operation. If damaged, have the power tool

repaired before use. Many accidents are caused by poorly maintained power tools.

f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking

into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation.

h) This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given

supervision or instruction concerning use of the appliance by a person responsible for their safety.

i) Children should be supervised to ensure that they do not play with the appliance.

5. Service

a. Haveyourpowertoolservicedbyaqualiedrepairpersonusingonlyidenticalreplacement

parts. This will ensure that the safety of the power tool is maintained.

b) If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly

qualied persons in order to avoid a hazard.

WARNING! When using mains-powered tools, basic safety precautions, including the

following,shouldalwaysbefollowedtoreduceriskofre,electricshock,personalinjuryand

material damage.

Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, before

operating the tool.

Save these instructions and other documents supplied with this tool for future reference.

The manufacturer cannot accept any liability for damage or accidents which arise due to a failure to follow these

instructions and the safety information.

Before you connect the appliance to the mains supply make sure that the data on the rating plate are

identical to the mains data.

This tool is double insulated therefore no earth wire is required.

The power supply for this product should be protected by a residual current device (rated at 30mA or less). A

residual current device reduces the risk of electric shock.

Note: Double insulation does not take the place of normal safety precautions when operating this tool. The

insulation system is for added protection against injury resulting from a possible electrical insulation failure

within the tool.

Using an Extension Lead

Always use an approved extension lead suitable for the power input of this tool. Before use, inspect the

extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or defective.

When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not

suitable for the power input of the tool or which is damaged or defective may result in a risk of re and electric

shock.

IMPORTANT! ALWAYS START THE CEMENT MIXER

BEFORE LOADING THE DRUM. LOAD THE DRUM WHILE

IT IS ROTATING.

IMPORTANT! DO NOT TURN THE MIXER OFF WHILE IT’S

FULL OF MATERIAL. EMPTY THE DRUM WITH THE DRUM

ROTATING.

IMPORTANT! ENSURE MATERIAL IS NOT LOADED INTO

THE MIXER ALL AT ONCE. ADD THE MATERIAL STEADILY

OVER THE MIXING BLADES, THIS HELPS TO AVOID

THE MATERIAL FROM STICKING TO THE BACK OF THE

DRUM.

WARNING!

1. DO NOT LET THE SHOVEL MOUTH OR ANY OTHER DEVICES

ENTER THE DRUM MOUTH DURING LOADING.

2. NEVER PLACE HANDS INSIDE THE REVOLVING DRUM OR

NEAR ANY ROTATING PARTS.

3. PLACE THE CEMENT MIXER AS CLOSE AS POSSIBLE TO THE

WORK SITE. DO NOT MOVE THE CEMENT MIXER WHEN LOADED.

4. RETIGHTEN ALL BOLTS ATTACHING MOTOR AND MOTOR

HOUSING ASSEMBLY, DRUM ASSEMBLY AND FRAME ASSEMBLY

AFTER FIRST MIX.

8. LOADING THE DRUM

Double insulated

Danger of electric shock

WARNING! ENSURE THE TOOL IS SWITCHED OFF AND

DISCONNECTED FROM THE POWER SUPPLY BEFORE

PERFORMING ANY OF THE FOLLOWING MAINTENANCE.

WARNING! DO NOT POUR OR SPRAY WATER DIRECTLY INTO

OR OVER THE MOTOR COVER.

2

4

2

2

2

6

4

M8 55

M8 65

M8 60

M8 20

M8 20

M8 30

M8 20

1

M10 70

2

10

2

4

M8 16 1

1

2

M8 25

4

4

4

8

MAINTENANCE

Note: Ozito Industries will not be responsible for any damage or injuries

caused by the repair of the cement mixer by an unauthorised person or by

mishandling of the mixer.

FAULT POSSIBLE CAUSES SOLUTION

The Cement

Mixer does not

start.

Not Connected to mains

power

Connect to mains power

Power cord or plug is

defective.

Contact Ozito customer

service.

Other electrical defect to the

product

Contact Ozito customer

service.

Cement Mixer

does not reach

full power

Extension cord not suitable

for operation with this product

Use suitable extension

cord..

Power source (e.g.

Generator) has too low

voltage.

Connect to another power

source.

Mixing volume is too large Reduce the amount of

material

Unsatisfactory

result

Mixer blades are dull/

damaged

Replace with new ones

Mixer blades not suitable for

work piece material

Use proper mixing blades

Excessive

vibration or

noise

Mixer blades are dull/

damaged.

Replace with new ones

Bolts/nuts are loose. Tighten bolts/nuts.

OZITO UK Unit 9 Stadium Court, Wirral International Business Park, Plantation Road, Bromborough, Wirral, CH62 3QG

All of our products undergo strict quality checks to ensure that they reach

you in perfect condition. In the unlikely event that your device develops a

fault, please contact our service department at the address shown on this

guarantee card. You can also contact us by telephone using the customer

service number shown. Please note the following terms under which

guarantee claims can be made:

1. These warranty terms regulate additional warranty services, which the

manufacturer mentioned below promises to buyers of its new products

in addition to their statutory guarantee claims are not affected by this

guarantee. Our guarantee is free of charge to you.

2. The warranty services only covers defects due to material or

manufacturing faults on a product which you have bought from the

manufacturer mentioned below are limited to either the rectication of said

defects on the product or the replacement of the product, whichever we

prefer.

Please note that our devices are not designed for use in commercial, trade

or professional applications. A guarantee contract will not be created if the

device has been used by commercial, trade or industrial business or has

been exposed to similar stresses during the guarantee period.

3. The following are not covered by our guarantee:

- Damage to the device caused by a failure to follow the assembly

instructions or due to incorrect installation, a failure to follow the operating

instructions (for example connecting it to an incorrect mains voltage or

current type) or a failure to follow the maintenance and safety instructions

or by exposing the device to abnormal environmental conditions or by lack

of care and maintenance.

- Damage to the device caused by abuse or incorrect use (for example

overloading the device or the use or unapproved tools or accessories),

ingress of foreign bodies into the device (such as sand, stones or dust,

transport damage), the use of force or damage caused by external forces

(for example by dropping it).

- Damage to the device or parts of the device caused by normal or natural

wear or tear or by normal use of the device.

4. Your Product is guaranteed for a period of 36 months from the original

date of purchase and is intended for DIY (Do It Yourself) use only. Warranty

excludes consumable parts. Guarantee claims should be submitted

before the end of the guarantee period within two weeks of the defect

being noticed. No guarantee claims will be accepted after the end of the

guarantee period. The original guarantee period remains applicable to the

device even if repairs are carried out or parts are replaced. In such cases,

the work performed or parts tted will not result in an extension of the

guarantee period, and no new guarantee will become active for the work

performed or parts tted. This also applies if an on-site service is used.

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST

RETURN THE PRODUCT TO THE PLACE OF PURCHASE WITH YOUR

REGISTER RECEIPT.

Please refer to the restrictions of this warranty concerning wearing parts,

consumables and missing parts as set out in the service information in

these operating instructions.

CUSTOMER SERVICE HELPLINE

GB: 0151 294 4488

IRL: 1850 882711

Ozito-diy.co.uk

ozito-diy.co.uk

ORIGINAL INSTRUCTIONS

Spare parts can be ordered from the Special Orders

Desk at your local Bunnings Warehouse or Homebase

store.

For further information, or any parts visit

www.ozito-diy.co.uk or contact Ozito Customer Service:

Great Britain: 0151 294 4488

Ireland: 1850 882711

E-mail: enquires@ozito-diy.co.uk

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Ozito CMX-125U Cementmixer. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Ozito. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Ozito CMX-125U Cementmixer in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Ozito Cementmixers
Meer handleidingen voor Cementmixers

Veelgestelde vragen over Ozito CMX-125U Cementmixer

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Ozito CMX-120 Cementmixer

Handleiding

Ozito PXMMS-120 Cementmixer

Handleiding

Ozito DMM-080 Cementmixer

Handleiding

Scheppach PM1400 Cementmixer

Handleiding

Rupes MX 1600E Cementmixer

Handleiding

Hyundai 56454 Cementmixer

Handleiding

Crown C3-C Cementmixer

Handleiding

Eibenstock MXT 100/2 Cementmixer

Gerelateerde categorieën