Handleiding Perel CMD02 Metaaldetector

Handleiding

CMD02_v2 VELLEMAN

5

c) Testing and using the detector

To learn how the detector reacts to different metals, you should test it before you use it the first time. You can test

the detector indoors and outdoors.

- INDOOR testing and use

NOTE: Never test the detector on a floor inside a building. Most buildings have metal of some kind in the floor,

which might interfere with the objects you’re testing, or mask the signal completely.

1. Slide the POWER switch to ON.

2. Select the operating mode.

3. Place the detector on a wooden or plastic table, and remove any watches, rings or metal jewellery you are

wearing.

4. Adjust the search coil so the flat part points towards the ceiling.

5. Slowly sweep a sample of the material you want the detector to find (such as a gold ring or a coin) 2-3

inches above the face of the search coil. When the detector detects any metal within the selected range, it

sounds a tone and an arrow appears below the target icon. The LCD displays the depth of the target.

NOTE: if you are using a coin, the detector will detect it more easily if you hold it so that a flat side is

parallel with the flat side of the search coil. A sweep with the side of the coin over the search coil might

cause false indication and unstable display of the arrow.

- OUTDOOR testing and use

1. Slide the POWER switch to ON.

2. Select the operating mode.

3. Find an area on the ground outside where there is no metal.

4. Place the material you want the detector to find (such as a gold ring or a coin) on the ground.

NOTE: If you are using a valuable metal sample such as gold to test the detector, mark the area where you

placed the item, to help you retrieve it later. Do not place it in tall grass or weeds.

5. Hold the search coil level to the ground about 1-2 inches above the surface, slowly move the search coil

over the area where you placed the sample, sweeping the search coil in a side-to-side motion.

6. If the detector detects the item, it sounds a tone, and an arrow and the depth appear on the display below

the target icon.

7. If the detector does not detect the item, make sure that the target mode is set correctly for the type of metal

you’re searching for. Also make sure that you’re moving the search coil correctly.

d) Search coil sweeping hints

- Never sweep the search coil as if it were a pendulum. Raising the search coil while sweeping or at the end of a

sweep will cause false readings.

- Sweep slowly. Hurrying will cause you to miss targets.

- It’s better you sweep the search coil from side to side in a straight line and keep the search coil parallel with the

ground.

- The detector responds with a signal when it detects most valuable metal objects. If a signal does not repeat after

you’ve swept the search coil over the target a few times, the target is probably junk metal.

- False signals can be caused by trashy ground, electrical interference, or large irregular pieces of junk metal.

- False signals are usually broken or non-repeatable.

e) Adjusting sensitivity

After you’ve become familiar with how your detector works, it’s important to fine tune the sensitivity to get a good

result. Press the touch button SENS on the panel. Then press Up or Dn to increase or decrease the sensitivity.

The level on the segment will be displayed form high to low position.

NOTE: in order to detect a target deeply buried, you can adjust the SENS to a high position. But don’t set the

SENS lever to MAX, because the detector will receive interference and false signal from broadcast antennae and

other electronic lines. The detector will have unstable arrow and irregular tone indications.

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Perel CMD02 Metaaldetector. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Perel. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Perel CMD02 Metaaldetector in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Perel Metaaldetectors
Meer handleidingen voor Metaaldetectors

Veelgestelde vragen over Perel CMD02 Metaaldetector

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Beoordeling

Gerelateerde producten

Handleiding

Garrett GTI 1500 Metaaldetector

Handleiding

Nokta Racer 2 Metaaldetector

Handleiding

Pyle PHMD74 Metaaldetector

Handleiding

Teknetics T2 Metaaldetector

Handleiding

Minelab Vanquish 540 Metaaldetector

Handleiding

Kayoba 002-163 Metaaldetector

Handleiding

Minelab GPX 7000 Metaaldetector

Handleiding

Viking VK30 Metaaldetector

Gerelateerde categorieën