Handleiding Poulan PL914 Kettingzaag

Handleiding

VIBRATION EXPOSURE

Exposure to vibrations through prolonged use of power

tools could cause blood vessel or nerve damage in the

¿QJHUVKDQGVDQGMRLQWVRISHRSOHSURQHWRFLUFXODWLRQ

disorders or abnormal swelling. Prolonged use in cold

weather has been linked to blood vessel damage in

otherwise healthy people. If symptoms occur such as

numbness, pain, loss of strength, change in skin color or

WH[WXUHRUORVVRIIHHOLQJLQWKH¿QJHUVKDQGVRUMRLQWV

discontinue the use of this power tool and seek medical

attention. An anti-vibration system does not guarantee

the avoidance of these problems. Users who operate

power tools on a continual and regular basis must closely

monitor their physical condition and the condition of the

power tool.

ASSEMBLY

a WARNING! Do not connect the power tool to the

power supply before it is completely assembled.

a WARNING! Always use gloves when handling the

chain.

ASSEMBLING THE GUIDE BAR AND CHAIN

Unpack all parts carefully and place the power tool on a

solid, level surface. Examine the power tool for damage.

Use the supplied combination tool (22) to loosen and

remove the lock nut (5), then remove the sprocket cover

(6). The chain tensioning bolt (19) must be aligned

with the corresponding hole in the guide bar (7, D). If

necessary, use the combination tool to turn the chain

tensioning screw (16) until the chain tensioning bolt is in

the proper position.

The running direction is marked with an arrow on the

sprocket cover (G). To determine the direction of cut, it

may be necessary to turn over the chain (4). Hold the

guide bar (7) vertically with the tip pointing upwards and

install the chain, beginning at the tip of the bar.

Place the guide bar with the chain on the guide bolt (18)

and chain tensioning bolt.

Place the chain around the chain sprocket (17) and make

sure it is correctly mounted (A).

Place the sprocket cover on top and tighten gently with the

lock nut using the combination tool.

TENSIONING THE CHAIN

a WARNING: Unplug the chain saw from the power

source before adjusting the chain tension.

Make sure the chain is inside the guide groove of the

guide bar.

Using the combination tool, turn the chain tensioning

screw clockwise. Pull upwards on the tip of the guide bar

while the chain is being tensioned.

Do not tension the chain too tightly. When cold, it should

be possible to lift the chain in the middle of the guide bar

approximately 5 mm (0.2 in). Tighten the lock nut securely.

5 mm

(0.2 in)

A new chain requires a running-in period of approximately

5 minutes. Chain lubrication is very important at this stage.

After running-in, check the chain tension and adjust if it is

necessary.

NOTE: A new chain will stretch. Check the chain

WHQVLRQIUHTXHQWO\ZKHQ¿UVWXVHGDQGWLJKWHQZKHQ

the chain becomes loose around the guide bar.

When warm, the chain will expand and slacken and there

is a danger of it jumping off the rail.

Tension the chain when it is necessary. If the chain is

tensioned when hot, it must be loosened again when

the sawing work has been completed. Otherwise, the

contraction which takes place as the chain cools can

result in excessively high tension.

ADDING GUIDE BAR AND CHAIN OIL

a &$87,217KHFKDLQVDZLVQRWVXSSOLHG¿OOHGZLWK

RLO,WLVQHFHVVDU\WR¿OOZLWKRLOEHIRUHXVH1HYHU

operate the chain saw without oil or at an empty oil

tank level, as this will damage the product.

a CAUTION: It is important to use only standard

guide bar and chain oil to avoid damage to the

chain saw. This type of oil can be found at the

location you purchased the chain saw or your

local hardware store. Never use recycled or old

oil. The use of non-approved oil will invalidate the

warranty.

Filling the oil tank:

1. Set the chain saw on any level surface with the oil tank

cap (14) facing upward.

2. Clean the area around the oil tank cap with a cloth and

unscrew the cap by turning it counterclockwise.

3. Pour oil into the oil tank opening (20) until the reservoir

is full. Make sure dirt or debris does not enter the oil

tank.

4. 5H¿WWKHRLOWDQNFDSDQGWLJKWHQLWE\WXUQLQJLW

clockwise until it is hand tight.

5. Wipe away any spilled oil.

To allow venting of the oil reservoir, small breather

channels are provided between the oil tank cap and the

strainer. To prevent leakage, make sure the chain saw is

stored in a horizontal position with the oil tank cap facing

upward when it is not in use.

To prevent excessive wear, the chain and guide bar must

be evenly lubricated during operation.

Lubrication is automatic. Never work without chain

lubrication. If the chain runs dry, the entire cutting

apparatus will quickly become severely damaged. It is

therefore important to check both chain lubrication and the

oil level gauge (15) every use.

Never use the saw when the oil level is below the “Min.”

mark on the oil level gauge. When the oil level is below

the “Min.” mark, add oil until the oil level reaches the

“Max.” mark.

9

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Poulan PL914 Kettingzaag. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Poulan. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Poulan PL914 Kettingzaag in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Poulan Kettingzagen
Meer handleidingen voor Kettingzagen

Veelgestelde vragen over Poulan PL914 Kettingzaag

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Poulan P4018AV BH Kettingzaag

Handleiding

Poulan PL1416 Kettingzaag

Handleiding

Poulan P3314WSA Kettingzaag

Handleiding

Poulan P3416 Kettingzaag

Handleiding

Poulan P3314WS Kettingzaag

Handleiding

Poulan P4018WM Kettingzaag

Handleiding

Poulan PRCS16i Kettingzaag

Handleiding

Poulan PL3816 Kettingzaag

Gerelateerde categorieën