Handleiding Princeton Tec League Zaklamp

Handleiding

brightness due to lower nominal voltage.

Some battery formulations can emit

hydrogen gas. This gas can create an

explosion potential in sealed devices if it

is not vented or removed.

Switch Operation

League 100’s switch locks in either on

or off position. From the off and locked

position, slide the lock forward then move

the switch right to turn the light on. Lock

switch by sliding the lock toward the back

of the light if desired.

O-Ring and Lens Cap

Occasionally clean and lightly lubricate

the O-ring and Lens Cap threads. Use

only silicone grease, never use aerosol

spray lubricants. Certain types of aerosol

sprays can cause damage the plastic and

void the warranty.

General Maintenance

As with any outdoor equipment, the light

should be kept clean with mild soap and

water. Avoid getting dirt on the o-ring and

in the threads of the lens cap. If this should

occur, take the light apart, remove the

o- ring, light module and batteries, then

clean the light body, lens and o ring re-lubricate

the o-ring and reassemble the light.

Troubleshooting

If the League 100 fails to light:

• Check the batteries for proper installation.

• Replace batteries if proper installation is

confi rmed.

• Check the light for water contamination.

The light will resume normal operation

once the water is shaken or blown out

and the light is left open until completely

dry. If the light has been contaminated

with salt water, fl ush the unit with fresh

water and dry as described above.

USA Lifetime Warranty

– International 10 Year Warranty

Princeton Tec warrants this product to

be free from defects in workmanship

and materials under normal use for

as long as you own this product.

This warranty covers all of the

component parts of the product

except batteries. This warranty does

not cover deterioration due to normal

wear or damage due to misuse,

alteration, negligence, accidents, or

unauthorized repair. Princeton Tec

will repair or replace parts which

are defective in workmanship or

materials.

Your authorized Princeton Tec

Dealer and Princeton Tec are the

only facilities authorized to repair

the product. After (3) unsuccessful

attempts (within the warranty period)

to repair the product, you have the

right to elect replacement of the

product or a refund of the purchase

price less allowance for use of

the product. NO INCIDENTAL OR

CONSEQUENTIAL DAMAGES ARE

INCLUDED IN THIS WARRANTY.

(Some states do not allow the

exclusion or limitation of incidental

or consequential damages, so the

above limitations or exclusions may

not apply to you.) This warranty

gives you specific legal rights, and

you may also have other rights which

vary from state to state.

Princeton Tec reserves the right

to change product specifications

without notice.

Return Policy

If your light fails to operate, follow these

simple steps:

1) Check batteries. Replace if

necessary.

2) Contact Princeton Tec customer

service at 800-257-9080 to request

an RMA number to send your light in

for repair or replacement. No warranty

repairs will be accepted without an RMA

number.

3) Return the light without batteries

to: Princeton Tec, 5198 Rt. 130,

Bordentown, NJ 08505. Postage due

and freight collect items will not be

accepted.

Princeton Tec

PO Box 8057,

Trenton, NJ 08650

Phone: 609-298-9331

Fax: 609-298-9601

www.princetontec.com

© 2013 Princeton Tec

LEAGUE

TM

LED FLASHLIGHT

Operating and Maintenance

Instructions

Notice d’utilisation et d’entretien

und Wartungsanleitung

www.princetontec.com

ENGLISH

Battery Installation – See Battery

Installation Diagram

• 4 AA

• Alkaline (LR03)

• Rechargeable NiCad or NiMH

NOTE: Rechargeable NiCad or NiMH

batteries may result in reduced brightness

due to lower nominal voltage.

Lithium batteries are not approved for use,

and will cause damage to League circuitry.

Princeton Tec cares about the

environment and recommends recycling

batteries. For more information about

battery recycling, please go to: www.

batteryrecycling.com.

To install the batteries, rotate the lens

bezel counter clockwise and remove

it. Remove the light module to access

the battery compartment. Holding the

light body horizontally with the external

switch facing down, insert the bottom

pair of batteries, negative end fi rst.

Next, insert the top pair of batteries,

positive end fi rst. Then, place the light

module into the body, taking care to

orient the microswitch correctly.

Finally, screw the bezel clockwise until

it covers both o-rings. Do not over

tighten the bezel, to minimize risk of

compromising the seal and fl ooding

the light. Improper installation of the

batteries will damage the light and void

the warranty.

When removing batteries for replacement

or long-term storage, hold the light

horizontally with the switch side down

and push the top battery in and down to

release it from the catch inside the body.

Tilt the open end of the light down until

the batteries slide into your free hand.

WARNING

• Never mix fresh and used batteries.

• Never mix different battery brands or

chemistry types.

• Always remove drained batteries

immediately.

• Remove batteries during long periods

of storage.

NOTE: Rechargeable NiCad or

NiMH batteries may result in reduced

Figure 2 – Battery Replacement Remplacement des piles Betriebsartenschalter

Figure 1 – Switch Operation Opération de commutation Schalterbetätigung

brightness due to lower nominal voltage.

SWITCH

brightness due to lower nominal voltage.

SWITCH

1 181

DISTANCE (Meters)

Maxbright

LED

• Princeton Tec calculates total burn time as the time it takes for the light source to produce a minimum of

0.25 lux at 2 meters. 0.25 lux is about the equivalent of a full moon on a clear night.

• Princeton Tec berechnet die Gesamtbrenndauer bezogen auf eine von der Stirnlampe erzeugte minimale

Beleuchtungsstärke von 0,25 Lux in 2 Meter Abstand. 0,25 Lux entsprechen in etwa der Beleuch-

tungsstärke des Vollmonds in einer klaren Nacht.

• Princeton Tec défi nit la durée totale d’éclairage comme le temps nécessaire à la source

lumineuse pour produire un minimum de 0,25 lux à 2 mètres. 0,25 lux équivaut à peu près à la

luminosité d’une pleine lune dans un ciel nocturne dégagé.

1

4

2

5

3

6

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Princeton Tec League Zaklamp. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Princeton Tec. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Princeton Tec League Zaklamp in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Princeton Tec Zaklampen
Meer handleidingen voor Zaklampen

Veelgestelde vragen over Princeton Tec League Zaklamp

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Princeton Tec Amp 3.5 Zaklamp

Handleiding

Princeton Tec Impact XL Zaklamp

Handleiding

Clas Ohlson GSFLC13 Zaklamp

Handleiding

Nitecore TM10K LTP Zaklamp

Handleiding

Nitecore EH1S Zaklamp

Handleiding

Nitecore P23i Zaklamp

Handleiding

DeWalt DCL183 Zaklamp

Handleiding

Clarke RWL 10 Zaklamp

Gerelateerde categorieën