Handleiding Seitron TAS022 Thermostaat

Handleiding

TA S02M 0001 AN 022761C5 291013

OVERVIEW

This device is an electronic room thermostat for

heating systems suitable for reliable and accurate

temperature regulation in commercial and industrial

premises as well as for home installation.

The room temperature can be sensed by the internal

sensor or a remote sensor (optional).

OPERATION

When the measured room temperature is below the

value set on the dial the thermostat turns the relay on

and, at the same time, turns the red LED on.

SETTING THE ROOM TEMPERATURE

The user can set the room temperature by moving

the dial to any desired temperature, as explained in

the former paragraph, between 6°C and 30°C.

KNOB ROTATION LIMITATION

It is possible to limit the rotation range for the set-

poin knob by following these steps:

1. Remove the knob by tilting it, eventually with the help

of a screwdriver placed in the slot (2).

2. Pick up the plastic pins (4) parked at one side of

the knob area and set them (5) as in the example

of Fig. 6. In this example the rotation range (6) is

reduced as in the shown angle.

INSTALLATION

a

WARNING

- To adjust properly room temperature, install the

thermostat about 1.5m from floor level, far from

heat sources, airstreams or particularly cold

walls (thermal bridges). When the remote

sensor is used in conjunction with the

thermostat, then this note is to be applied to the

remote sensor itself.

- For remote version all wirings must be made

using wires with 1,5 mm² minimum cross

section and no longer than 25 m. Do not use

same duct for signal wires and mains.

- The appliance must be wired to the electric

mains through a switch capable of

disconnecting all poles in compliance with the

current safety standards and with a contact

separation of at least 3 mm in all poles.

- Installation and electrical wirings of this

appliance must be made by qualified

technicians and in compliance with the current

standards.

- Before wiring the appliance be sure to turn the

mains power off.

For installation the thermostat follow these steps:

1. Remove the knob by tilting it, eventually with the

help of a screwdriver placed in the slot.

2. Remove plastic cover by moving to the inner side,

through the use of a tool (Fig. 4), the two plastic

teeth (3) located on the left side (Fig. 3) of the

thermostat.

3. Fix the thermostat base plate to the wall through

the two screw holes with distance between axes of

60 mm.

4. Make the electrical connections, routing the wires

through the rectangular opening (8) and following

to the diagram of Fig. 4.

- ENGLISH -

3

5. Close the thermostat by carefully positioning the

cover so that the LED matches the relevant hole

and then by slightly pressing the cover in order to

make the four plastic teeth snapping. Then insert

the knob.

NIGHT SET BACK

In order to select the 'Night Set Back' feature an

external dry contact can be connected to terminal 6

(Fig. 5).

This mode results in reducing the temperature set

with the external dial by an amount set with the

internal trimmer (7) in Fig. 7, in the range 2°C .. 7°C.

The thermostat leaves the factory with the trimmer

set on 4.5°C.

SELECTION INTERNAL/EXTERNAL SENSOR

The thermostat leaves the factory configured by

default for operation with the internal temperature

sensor. If it is planned to install a remote sensor,

remove the jumper connector JP1 (8 of Fig. 7) and

connect an NTC type sensor (4700 ohm@ 25°C)

with a suitable beta value to terminals 7 and 8. In

case of doubt as to the type of sensor to connect,

please consult the manufacturer.

TECHNICAL FEATURES

Power supply:

TA S01M 0001: 230V~ -15% +10% 50Hz

TA S012 0001: 24V~ ±10% 50Hz

Power absorption:

TA S01M 0001: 5,3VA

TA S012 0001: 0,3VA

Regulation range: 6°C .. 30°C

Night set back: 2°C .. 7°C adjustable

(Default 4,5°C)

Differential: 0,5°C

Internal sensor type: NTC 4,7kΩ @ 25°C

Remote sensor optional: NTC 4,7kΩ @ 25°C

(optional)

Contact rating: 5 (1) A @ 250V~ SPDT

Protection grade: IP 30

Operating temperature: 0°C .. 40°C

Storage temperature: -10°C .. +50°C

Humidity limits: 20% .. 80% RH

(non condensing)

Case: Material: ABS self extinguishing V0

Color: Signal white (RAL 9003)

Size: 85 x 85 x 31 mm (W x H x D)

Weight: TA S01M 0001: ~135 gr.

TA S012 0001: ~ 130 gr.

NORMATIVE REFERENCES

The product complies with the following standards

(EEC 2004/108/c and 2006/95/c):

CEI-EN-60730-1 (2002)

CEI-EN-60730-2-9 (1998)

WARRANTY

The manufacturer is committed to the continual

development of its products and hence reserves the

right to change technical specifications and

performance features without notice. Consumers are

provided with a warranty against product non-

conformity in accordance with European Directive

1999/44/EC and the manufacturer’s guarantee policy.

The complete text of the warranty is available on

request from the seller.

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Seitron TAS022 Thermostaat. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Seitron. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Seitron TAS022 Thermostaat in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Seitron Thermostaten
Meer handleidingen voor Thermostaten

Veelgestelde vragen over Seitron TAS022 Thermostaat

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Seitron TAN01M Thermostaat

Handleiding

Seitron TAS01M Thermostaat

Handleiding

Seitron TAEZN4MC Thermostaat

Handleiding

Seitron TPER00MI Thermostaat

Handleiding

Seitron TFD01M0001SE Thermostaat

Handleiding

Seitron TCD01B Thermostaat

Handleiding

Seitron TCEDGTBI Thermostaat

Handleiding

Seitron TAEKW02D Thermostaat

Gerelateerde categorieën