Handleiding SentrySafe MS0100 Kluis

Handleiding

Optional kit (Fig. A) contains

(included on select models only):

• (2) Lag screws

• (2) Washers

• (2) Masonary anchors

Tools needed for floor mounting:

• Drill

• Wrench

• 7⁄16" (11.0 mm) drill bit

Wood anchoring:

9⁄32" (7.2 mm) drill bit

Masonry anchoring:

3⁄8"(9.50 mm) drill bit

Instructions:

1. Tip the safe onto its right side. (Door

hinges horizontal with the floor.)

2. Unlock the safe and open the door.

3. Look on the bottom of the safe for two

indentations on the feet in opposite

corners. Using the 7⁄16" (11.0 mm) bit,

drill a hole through each indentation

perpendicular to the bottom of the safe

(Fig. B). Do not drill from any location

inside the safe.

4. Close the door and tip the safe upright.

Place it where desired and reopen the

door.

5. Use a screw or drill bit to mark the floor

through both holes. (Fig. C)

6. Move the safe aside to clear both marked

spots for drilling.

7. Drill into the floor:

A. For wood: Using the wood drill bit,

drill a hole 2-1⁄2" (64 mm) deep in each

marked spot. (Fig. D)

B. For masonry: Using the masonry bit,

drill a hole 2-1⁄2" (64 mm) deep in each

marked spot. (Fig. D) Install a masonry

anchor in each hole.

8. Replace the safe in the desired position,

with the holes in the safe aligned with

those in the floor.

9. Securing the safe:

A. For wood: Pass each lag screw through

a washer, then through the safe and into a

hole. Tighten with the wrench. (Fig. E)

B. For masonry: Pass each lag screw

through a washer, then through the safe

and into a masonry anchor. Tighten with

the wrench. (Fig. F)

NOTE: Drill holes through feet only, not through

the back or sides. Bolting/unbolting of the unit is

at the consumers expense and discretion. Sentry

Group is not responsible for any costs incurred if

the unit is to be replaced.

4

Floor Mount (optional)

XY1234

Troubleshooting

• If electronics are not functioning, replace

batteries first (behind electronic lock case)

as described in step one of this guide.

• If electronics are functioning and you cannot get

into safe:

- Pull handle up

- Follow instructions for opening your lock type.

• You must use both the key (if equipped) and the

electronic code to open the safe if the key lock

cylinder is pushed in.

Delay mode

Enters a two-minute delay mode after an invalid

code has been entered three consecutive times.

In this mode, the lock can not be activated and

any key entry will generate an ERROR signal.

Sentry

®

Safe First-Class Customer Care

If you lose your combination/keys or need accessories, we can help!

Visit our website at www.sentrysafe.com

Please note: Your safe’s serial number is required

to obtain replacement combination/keys. The serial

number can be found near the door hinge as

shown or at the beginning of this guide.

Registration: To be eligible for warranty coverage, the original purchaser must register

the product online at www.sentrysafe.com or complete and return to Sentry Group

the enclosed registration card.

WARNING

DO NOT store delicate

items directly in your safe.

SentrySafe products which offer fire

protection have a proprietary insulation that

has a high moisture content. In addition

the SentrySafe advanced safes close airtight

to offer water resistance, which may also

cause moisture to accumulate inside your

safe. The desiccant packet included in your

safe during shipment, should be left in your

safe. DO NOT DISCARD IT. It is intended

to help absorb moisture which may

accumulate inside your safe. Please open

your unit periodically to avoid moisture

accumulation.

If you choose to store delicate items such

as jewelry with working parts, watches,

stamps, or photos in your safe, we

recommend putting them in an air-tight

container, prior to placing them in the safe

for storage.

NOTE: Sentry Group will not be responsible

for any damage or loss of items placed in

the unit due to moisture.

WARNING

DO NOT store pearls

in this safe unit.

In the event of a fire, potential damage to

delicate pearls occurs at temperatures much

lower than the 350°F interior performance

measure which the UL classification

performance standard indicated guarantees.

Therefore, DO NOT store pearls in your

SentrySafe product.

WARNING

No computer disks, audio-visual

media or photo negatives.

This product is not intended to protect

computer floppy or diskettes, cartridges

and tapes, audio or video cassettes or

photo negatives. For fire-resistant storage

of these materials, ask your

retailer for

the SentrySafe Fire-Safe Media storage

products.

3-English

B

A

D

E

F

C

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je SentrySafe MS0100 Kluis. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met SentrySafe. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van SentrySafe MS0100 Kluis in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor SentrySafe Kluizen
Meer handleidingen voor Kluizen

Veelgestelde vragen over SentrySafe MS0100 Kluis

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Beoordeling

Gerelateerde producten

Handleiding

SentrySafe T6-3L1 Kluis

Handleiding

SentrySafe SFW082F Kluis

Handleiding

SentrySafe QAP1E Kluis

Handleiding

SentrySafe CHW20221 Kluis

Handleiding

SentrySafe S0310 Kluis

Handleiding

SentrySafe PL048E Kluis

Handleiding

SentrySafe PB2K Kluis

Handleiding

SentrySafe SFW123BSC Kluis

Gerelateerde categorieën