Handleiding Sony M-675V Cassetterecorder

Handleiding

M-675V/673V/670V.GB/ES.3-259-967-16(1).U/U2

To monitor the sound

Connect an earphone (not supplied) firmly to the EAR jack. The

monitor volume cannot be adjusted by VOL.

To prevent a cassette from being accidentally recorded

over

Break off and remove the cassette tabs. To reuse the cassette for

recording, cover the tab hole with adhesive tape.

Recording from Various Sound Sources

Notes

• When you are going to record something that you may not have an

opportunity to record again, test the unit first before you actually start

recording.

• When recording with an external microphone, the VOR system may not

work properly because of the difference in sensitivity.

Recording with an External Microphone

Connect a microphone firmly to the MIC jack.

M-673V : use the supplied microphone.

Other models : use a microphone of low impedance (less than 3

kΩ). When using a plug-in-power system microphone, the

power to the microphone is supplied from this unit.

Recording from another equipment

Connect another equipment firmly to the MIC jack using the

connecting cord (not supplied).

Set this unit to the recording mode and another equipment to

the playback mode.

Playing a Tape

1 Insert a cassette with the side to start playing facing the lid.

2 Select the tape speed to the same speed as that used for

recording.

3 Press n.

4 Turn VOL to adjust the volume. There is a tactile dot beside

VOL on to show the direction to turn up the volume.

At the end of the tape, playback stops and the unit turns off

automatically (Automatic shut-off mechanism). After the tape

has been wound or rewound, be sure to press Tx.

If you plug in headphones (not supplied) to the EAR jack, you

will get monaural output from both left and right channels.

To Press or slide

Stop playback/stop fast Tx

forward or rewind

Pause playback Slide >PAUSE in the direction of the

arrow. REC/BATT lamp goes off.

To release pause

playback

, release

>

PAUSE*.

Fast forward** (FF) Slide FF/CUE m•M REW/REVIEW

toward FF/CUE m during stop.

Rewind** (REW) Slide FF/CUE m•M REW/REVIEW

toward M REW/REVIEW during stop.

Search forward during Keep FF/CUE m•M REW/REVIEW

playback (CUE) pushed toward FF/CUE m during playback

and release it at the point you want.

Search backward during Keep FF/CUE m•M REW/REVIEW

playback (REVIEW) pushed toward M REW/REVIEW during

playback and release it at the point you want.

Start recording during z

playback

* >PAUSE will also be automatically released when Tx is pressed

(stop-pause-release function).

**If you leave the unit after the tape has been wound or rewound, the

batteries will be consumed rapidly. Be sure to press Tx.

Note

If the tape is completely rewound while searching backward during

playback (REVIEW), the FF/CUE m•M REW/REVIEW switch may

not return to the center position when you release the switch. In this case,

push back the switch to the center to start playback.

To increase the playback speed

Slide the FAST PB. switch in the direction of the arrow. The

playback speed will be increased.

To return to the original speed, slide the FAST PB. switch to

the original position.

Precautions

On power

• Operate the unit only on 3 V DC.

For AC operation, use the AC power adaptor recommended for the

unit. Do not use any other type. For battery operation, use two size

AAA (R03) batteries.

On the unit

• Use only the (standard microcassettes) with this unit.

Non-standard cassettes cannot be used because their “L” dimension

(see illustration) is different.

Standard Non-standard

• Do not leave the unit in a location near heat sources, or in a place

subject to direct sunlight, excessive dust or mechanical shock.

• Should any solid object or liquid fall into the unit, remove the batteries

or disconnect the AC power adaptor, and have the unit checked by

qualified personnel before operating it any further.

• Keep personal credit cards using magnetic coding or spring-wound

watches, etc. away from the unit to prevent possible damage from the

magnet used for the speaker.

• When you do not use the unit for long, remove the batteries to avoid

damage caused by battery leakage and subsequent corrosion.

• If the unit has not been used for long, set it in the playback mode and

warm it up for a few minutes before inserting a cassette.

For customers in the USA and Canada

RECYCLING NICKEL METAL HYDRIDE BATTERIES

Nickel Metal Hydride batteries are recyclable.

You can help preserve our environment by returning your

used rechargeable batteries to the collection and recycling

location nearest you.

For more information regarding recycling of rechargeable

batteries, call toll free 1-800-822-8837, or visit http://

www.rbrc.org/.

Caution: Do not handle damaged or leaking Nickel Metal Hydride

batteries.

If you have any questions or problems concerning your unit, please

consult your nearest Sony dealer.

Troubleshooting

Should any problem persist after you have made these checks,

consult your nearest Sony dealer.

You cannot close the cassette compartment lid.

t The cassette is being inserted in the wrong way.

t n has been already pressed.

t The cassette is not being inserted completely.

The unit does not operate.

t The batteries have been inserted with incorrect polarity.

t The batteries are weak. Replace both batteries with new

ones.

t >PAUSE is slid in the direction of the arrow.

t The AC power adaptor is not firmly connected.

t The unit will not run on dry batteries if the AC power

adaptor is left plugged into the DC IN 3V jack even

though you disconnect the AC power adaptor from the

power source.

Recording cannot be made.

t There is no cassette in the cassette compartment.

t The tab on the tape has been removed. To reuse the tape

for recording, cover the tab hole with adhesive tape.

t The batteries are weak. Replace both batteries with new

ones.

Recording is interrupted.

t The VOR switch is set to ON. When you do not use VOR,

set it to OFF.

Recording cannot be erased completely.

t The head is contaminated. See “Maintenance”.

Playback cannot be made.

t The tape has reached the end. Rewind the tape.

No sound comes from the speaker.

t The earphone is plugged in. Unplug it.

t The volume is turned down completely.

The sound drops out or comes with excessive noise.

t The volume is turned down completely.

t The batteries are weak. Replace both batteries with new

ones.

t The head is contaminated. See “Maintenance”.

t Direct placement of the cassette tape on the speaker

resulted in magnetization and deteriorated tonal quality.

t Use the unit away from radiowave-emitting devices such

as cellular phones.

Tape speed is too fast or too slow or the sound is

distorted in the playback mode.

t Improper setting of the TAPE SPEED switch. Set it to the

same speed as that used for recording.

t The FAST PB. switch is slid in the direction of the

arrow.

t The batteries are weak. Replace both batteries with new

ones.

During CUE/REVIEW the tape stops or does not run.

You cannot fast-forward or rewind.

t The batteries are weak. Replace both batteries with new

ones.

Maintenance

To clean the tape head and path

Press n and wipe the head, capstan and the pinch roller with a

cotton swab, moistened with alcohol every 10 hours of use.

To clean the exterior

Use a soft cloth slightly moistened in water. Do not use alcohol,

benzine or thinner.

Specifications

Tape

(normal position type)

Recording system

2-track 1-channel monaural

Speaker

Approx. 2.8 cm (1

1

⁄8 in.) dia.

Tape speed

2.4 cm/s (

15

⁄16 ips), 1.2 cm/s (

15

⁄32 ips)

Frequency range

300 - 4 000 Hz (with TAPE SPEED switch at 2.4 cm/s)

Input

Microphone input jack (minijack/monaural/PLUG IN POWER)

sensitivity 0.2 mV for 3 kΩ or lower impedance microphone

Output

Earphone jack (minijack/monaural) for 8 - 300 Ω earphone

Power output (at 10% harmonic distortion)

450 mW

Power requirements

3 V DC batteries size AAA (R03) × 2/External DC 3V power sources

Dimensions (w/h/d) (incl. projecting parts and controls)

Approx. 54.8 × 106.8 × 21.5 mm (2

1

⁄4 × 4

1

⁄4 ×

7

⁄8 in.)

Mass (main unit only)

Approx. 92 g (3.3 oz)

Supplied accessories

AC power adaptor (1) (M-675V only), Battery charge adaptor (1) (M-

675V only), Rechargeable batteries NH-AAA, 1.2 V, typ. 1 000 mAh,

Ni-MH (2) (M-675V only), Microcassette tape MC-30 (1) (for the

United States and Europe only), Alkaline batteries LR03 (SG) (2) (M-

673V, M-670V for the United States only), Microphone (1) (M-673V

only), Carrying pouch (1) (M-673V only), Battery carrying case (1) (M-

675V only)

Design and specifications are subject to change without notice.

This warranty is valid only in the

United States.

M-675V/673V/670V

Operating Instructions

Manual de instrucciones (en el reverso)

© 2004 Sony Corporation Printed in China

3-259-967-16 (1)

Microcassette

™

-Corder

For customers in the United States

Owner’s Record

The model number is located at the back of the unit and the

serial number is located inside the cassette holder. Record

these numbers in the spaces provided below. Refer to these

numbers whenever you call upon your Sony dealer

regarding this product.

Model No._________________ Serial No._________________

Product registration

Please register this product on line at www.sony.com/

productregistration

<http://www.sony.com/productregistration>

Proper registration will enable us to send you periodic

mailings about new products, services, and other important

announcements. Registering your product will also allow us

to contact you in the unlikely event that the product needs

adjustment or modification. Thank you.

You are cautioned that any changes or modifications not

expressly approved in this manual could void your authority

to operate this equipment.

WARNING

To prevent fire or shock hazard, do not

expose the unit to rain or moisture.

About This Manual

The instructions in this manual are for 3 models. There is no

difference among M-675V, M-673V and M-670V except for the

supplied accessories. M-675V/M-673V consists of M-670V

Microcassette recorder and the accessories. For information about

the supplied accessories, see “Specifications” of this manual.

Preparing Power Sources

Choose one of the following power sources.

Dry Batteries

Make sure that nothing is connected to the DC IN 3V jack.

1 Open the battery compartment lid.

2 Insert two size AAA (R03) batteries with correct polarity and

close the lid.

To take out the batteries

To attach the battery compartment lid if it is

accidentally detached

When to replace the batteries

Replace the batteries with new ones of the same kind when the

REC/BATT lamp dims and the E lamp flashes.

Notes

• The unit will play back normally for a while, even after the E lamp

flashes. However, replace the batteries as soon as you can. Otherwise,

the built-in speaker may emit a loud noise and recordings may not be

made correctly.

• In the following cases you do not need to replace the batteries:

– if the E lamp flashes with the playback sound when you turn up the

volume.

– if the E lamp lights momentarily when the tape starts running or at

the end of the tape.

– if the E lamp flashes during FF/REW or CUE/REVIEW.

Battery life* (Approx. hours)

Batteries Recording Playback**

Sony alkaline LR03 (SG)*** 14.5 9

Sony manganese R03 (SB) 5 2.5

NH-AAA (M-675V only) 10 6

* Measured valued by the standard of JEITA (Japan Electronics and

Information Technology Industries Association) (Using a Sony

Microcassette)

** Using a tape on which music has been recorded is played at volume

setting 7 using speaker

***When using Sony LR03 (SG) alkaline dry batteries (produced in Japan)

Note

The battery life may be shorter depending on the operating condition, the

surrounding temperature and battery type.

For maximum performance we recommend that you use

alkaline batteries.

House current

Connect the AC power adaptor to DC IN 3V and to a wall outlet.

Use the AC-E30HG AC power adaptor (not supplied)

or the supplied AC power adaptor (M-675V only) .

Do not use any other

AC power adaptor.

Insert the

batteries with

correct polarity.

Notes

• Specifications for AC-E30HG vary for each area. Check your local

voltage and the shape of the plug before purchasing.

• Do not touch the AC power adaptor with wet hands.

• Connect the AC power adaptor to an easily accessible AC outlet. Should

you notice an abnormality in the AC power adaptor, disconnect it from

the AC outlet immediately.

Rechargeable batteries (supplied with

the M-675V only)

Charge the supplied rechargeable batteries only with the

supplied charge adaptor and the supplied AC power adaptor

before using them.

Full charging takes about 12 hours. While charging, the

CHARGE indicator lights up, and when charging is completed,

it goes off. The unit can be used for recording for approximately

12 hours with fully charged rechargeable batteries.

To charge

Recharge the two rechargeable batteries together.

To take out the rechargeable batteries from the charge adaptor,

push the # side of the battery first and then remove the 3 side.

To use

• When using the supplied charge adaptor, charge the rechargeable

batteries specified on the charge adaptor only. Do not charge any other

batteries.

• When charging, use the supplied AC power adaptor only.

• If there is distortion of sound or excessive noise, or if the unit does not

operate properly, turn off the unit and recharge the two rechargeable

batteries together.

• The rechargeable batteries will discharge gradually even when not in

use. Be sure to charge them before use.

• Charging and operation should be made in temperature ranges 5°C to

40°C (40°F to 104°F).

• The charge adaptor will become warm during charging but this is not a

sign of problem.

• Do not use or leave the charge adaptor, AC power adaptor and

rechargeable batteries in a location near heat sources or in a place

subject to direct sunlight or excessive moisture.

• Unplug the AC power adaptor from the wall outlet when it is not to be

used for long.

• Do not charge dry batteries.

Recording

You can record right away with the built-in microphone.

Make sure that nothing is connected to the MIC jack.

1 Press the reset button of the tape counter.

2 Press Tx and insert a standard microcassette with the side

to start recording facing the lid.

3 Select the desired tape speed.

2.4 cm for optimum sound (recommended for normal use):

A 30-minute recording can be made using both sides of the

MC-30 microcassette (supplied for the United States and

Europe only). There is a tactile dot on this side.

1.2 cm for longer recording time: A 60-minute recording can

be made using both sides of the MC-30 microcassette

(supplied for the United States and Europe only).

4 Set VOR to OFF.

If you set VOR to ON, the unit automatically starts

recording the sound and pauses when there is no sound

(you can save tapes and batteries).

When the sound is not loud enough, set it to OFF, or the unit

may not start recording.

5 Press z. n is pressed simultaneously and recording starts.

While the tape runs, the REC/BATT lamp lights and flashes

depending on the strength of the sound.

Recording level is fixed.

At the end of the tape, recording stops and the unit turns off

automatically (Automatic shut-off mechanism).

To Press or slide

Stop recording Tx

Pause recording

Slide >PAUSE in the direction of the arrow.

To release pause recording, release

>

PAUSE*.

Start recording during z during playback (the unit enters the

playback recording mode)

Review the portion just Push up FF/CUEm•MREW/REVIEW

recorded toward MREW/REVIEW during the

recording. Release the button at the point to

start playback.

Take out a cassette Tx

* >PAUSE will also be automatically released when Tx is pressed

(stop-pause-release function).

Note

Select the 2.4 cm tape speed for recording, if you play back the recorded

tape with another unit. Otherwise, the sound quality may be changed.

Notes on VOR (Voice Operated Recording)

• The VOR system is affected by the environmental recording conditions.

When you use the system in a noisy place, the unit will stay in the

recording mode. If the sound is too soft, on the contrary, the unit will

not start recording. If you cannot get the results you want, set it to OFF.

• The VOR system may not record the beginning of the sound you want

to record because it starts recording only after it catches the sound. For

an important recording, set it to OFF.

Insert the

batteries with

correct polarity.

Polarity of the plug

Charge

adaptor

to a wall outlet

CHARGE

indicator

Rechargeable batteries NH-AAA

To a wall outlet

AC power adaptor

Approx. 5 mm

Only standard microcassettes have a

small indention of side A.

Approx. 2.5 mm

AC power adaptor

(supplied with M-675V only)

Head

Pinch roller

Capstan

VOL*

n*

>PAUSE

Tx

FAST PB.

TAPE SPEED*

FF/CUE m•

M REW/REVIEW

EAR

E (Battery

alert LED)

* The button has a

tactile dot.

> PAUSE

Tx

EAR

VOR

TAPE SPEED*

Tape counter

z

Tx

Microphone

REC/BATT

FF/CUE m•

M REW/REVIEW

VOL*

Tape counter

reset button

MIC (PLUG IN

POWER)*

E (Battery alert

LED)

* The button/jack

has a tactile dot.

GB+1U2.p65 2/26/08, 4:44 PM1

7

7

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Sony M-675V Cassetterecorder. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Sony. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Sony M-675V Cassetterecorder in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Sony Cassetterecorders
Meer handleidingen voor Cassetterecorders

Gerelateerde producten

Handleiding

Sony M-427 Cassetterecorder

Handleiding

Sony WM-EX405 Walkman Cassetterecorder

Handleiding

Sony M-640V Cassetterecorder

Handleiding

Sony WM-FX183 Walkman Cassetterecorder

Handleiding

Sony M-730V Cassetterecorder

Handleiding

Sony M-670V Cassetterecorder

Handleiding

Sony M-335 Cassetterecorder

Handleiding

Sony WM-WE1 Walkman Cassetterecorder

Gerelateerde categorieën