Handleiding Watts BT DPRF-01 Thermostaat

Handleiding

37

5 Parameter’s menu

Your thermostat has a parameter’s menu, in order

to enter in this menu, press and maintain the edition

key () during 5sec. Then parameter menu will

appear and first parameter screen will be displayed:

Now you can select a parameter which must be

adjusted with the navigation keys (◄) or (►), once

the parameter chosen, toggle the value with the

(OK) key, modify it with (-) or (+) and confirm your

adjustment with (OK).

38

To leave the parameter menu, choose the

parameter « End » and press (OK).

N° Default value & other possibilities

0

0

RF INI: Radio configuration

Sends the radio link signal in order to assign this RF

Thermostat with it’s RF receiver.

You also need to set simultaneously the receiver in

radio configuration mode (On a simple receiver press

and maintain button until the green light lit’s up, see

receiver leaflet)

0

1

dEG: Unit of the temperatures displayed

°C Celsius

°F Fahrenheit

0

2

__:__ Selection of the Time clock unit

24H (24:00)

12H (12:00 AM /PM)

0

3

dst: Daylight Summer time change Summer<->Winter

YES automatic change according to date.

no no daylight summer time automatic change.

39

0

4

AirC: Calibration of the internal probe

The calibration must be done after 1 day working with

the same setting temperature in accordance with the

following description:

Put a thermometer in the room at 1.5M distance from

the floor (like the thermostat) and check the real

temperature in the room after 1 hour.

When you enter on the calibration parameter “no” is

displayed on the right to indicate no calibration has

made.

To enter the value shown on the thermometer, use the

(-) or (+) keys to enter the real value. Then, press (Ok)

to confirm.

The message “Yes” should be displayed; the value will

be stored in the internal memory.

If you need to erase a calibration press on the escape

key ().

The old value will be erased and the message “no” will

be displayed.

* Pay attention:

Only the heating element driven by the thermostat must

be used during the complete step of the calibration.

40

05

OutC , AMbC , FlrC: Calibration of the external

wired probe

Same calibration method as described in parameter

“04 AirC” above.

06

HG: Anti-freeze temperature used in Holiday mode

Default value 10°C.

Use the (-) or (+) keys to change the anti-freeze setting

temperature. Then press (Ok) to confirm.

07

ITCS: YES, no

The Intelligent Temperature Control System will

activate your installation in advance (2 hours

maximum) to assure the desired temperature at the

hour programmed following your weekly program.

This automatic control system works in the following

way:

When you start your thermostat for the first time, it will

measure the time taken by your installation to reach

the set temperature. The thermostat will re-measure

this time at each program change to compensate

external temperature change & influence. You can now

program your thermostat without the need to adjust the

temperature in advance because your thermostat does

it automatically for you.

41

0

8

Clr ALL: Reset to Factory setting

Press and maintain (Ok) key during 10s to reset Set

points temperatures and user parameters in this menu

to factory default settings. User programs will also be

resetted.

* Pay attention:

Ensure you that you have all necessary elements to re-

setup your installation before to use this function.

09

Software version

VErS ___

10

End: Exit the parameter’s menu

Press (OK) key to exit installation parameter menu and

return to normal operation.

42

6 Technical characteristics

Environmental:

Operating temperature:

Shipping and storage

temperature:

0°C - 40°C

-10°C to +50°C

Electrical Protection

Installation Category

Pollution Degree

IP30

Class II

2

Measured temperature

precision

0.1°C

Setting temperature range

Comfort, Reduced

Holiday (Antifreeze)

Timer

5°C to 35°C by 0,5°C step

10°C (adjustable)

5°C to 35°C

Regulation characteristics

Proportional Band (PWM

2°C for 10min cycle) or

Hysteresis of 0.5°C

Power Supply

Operating life

2 AAA LR03 1.5V Alkaline

~2 years

Sensing elements:

Internal & External (option)

NTC 10k at 25°C

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Watts BT DPRF-01 Thermostaat. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Watts. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Watts BT DPRF-01 Thermostaat in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Watts Thermostaten
Meer handleidingen voor Thermostaten

Veelgestelde vragen over Watts BT DPRF-01 Thermostaat

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Watts BT 050 Chrono Battery Thermostaat

Handleiding

Watts BT-DRF-02 Thermostaat

Handleiding

Watts BT-DPRF-02 Thermostaat

Handleiding

Watts BT 051 Chrono Battery Thermostaat

Handleiding

Salus 091FLv2 Thermostaat

Handleiding

Maico THR 10 Thermostaat

Handleiding

Eberle RTR-E 6732 Thermostaat

Handleiding

AlpicAir TH-1732C(0-10V) Thermostaat

Gerelateerde categorieën