Home > Tuin & Terras > Waterpompen > Clarke Waterpompen > Clarke CBM 240 Waterpomp

Handleiding Clarke CBM 240 Waterpomp

Handleiding voor je Clarke CBM 240 Waterpomp nodig? Hieronder kun je de handleiding gratis bekijken en downloaden als PDF in het Nederlands en/of Engels. Dit product heeft 0 veelgestelde vragen, 0 comments en heeft 0 stemmen. Is dit niet de handleiding die je zoekt, neem dan contact met ons op.

Is je product kapot en biedt de handleiding geen oplossing meer? Dan kun je voor reparatie gratis terecht bij Repair Café.

Handleiding

CPE100TF, CBM100SS, CBM130SS and CBM250SS

These units are set up as a BOOSTER pumps by utilising an air chamber with a pressure

regulator to provide a constant pressure at the outlet. All models are provided with

non-return valves and Model CPE100TF is also provided with an inlet filter.

The pumps will automatically cut in when the water pressure reduces to 2.0 Bar,

and cut out when the pressure reaches 3.5 Bar. (These pressures are 3.5 and 5.2

bar respectively for Model CBM250SS). These pressures are factory set and must

not be altered. The pump may continue to operate for a short while, after the tap

is turned off, until the cut-out pressure is reached.

In order for the system to operate correctly, it is necessary to pressurise the air

chamber to 1.5 Bar (22psi), which is carried out as follows:

Unscrew the large protection cap on the end of the air chamber to reveal the air

valve, and use an air line or foot pump to charge the chamber to the specified

pressure, checking with a standard air pressure gauge until satisfied. Remember

to replace the protection cap when completed.

IMPORTANT: This procedure MUST be carried out BEFORE connecting to the water supply.

PRIMING

When suction lift is used to draw water into the pump it is essential that all

connections and hoses are completely air tight, otherwise the system will not work.

Although the pump is a ‘self priming’ type, it is nevertheless necessary to completely

fill the inlet side of the pump with water before being started for the first time, or if

the system has been drained for maintenance or repair purposes. This is known as

priming the pump and is carried out as follows :-

1. Locate and remove the small filler plug, situated on the top of the pump

chamber, and slowly fill the pump with water until all air is expelled.

NOTE: If a filter is fitted to your pump it is recommended that you remove the

brass plug on top of the unit, and fill the bowl with water.

In the case of the CPE100P, no filler plug is provided, and the pump body is

therefore filled through the outlet port before its’ connection

2. Adjust any device which may be fitted to the outlet side of the pump, so as to

ensure as great a flow as possible.

3. Switch on the pump and check for leaks. Water should start to flow through

the system after a short while. If, after 2-3 minutes, depending upon the suction

depth, water does not flow, check to ensure:

a) The inlet pipe is completely secure and completely free from defects.

Even a pin hole could prevent the pump from drawing water. This is the

most common problem encountered when operating water pumps.

b) The pump body has been primed correctly, and is completely filled with water.

NOTE: If the pump is gravity or pressure fed, priming will not be necessary, as

the pressure of water will purge the system of air.

Beoordeling

Laat ons weten wat je van de Clarke CBM 240 Waterpomp vindt door een beoordeling achter te laten. Wil je je ervaringen met dit product delen of een vraag stellen? Laat dan een bericht achter onderaan de pagina.

Bent u tevreden over de Clarke CBM 240 Waterpomp?
Ja Nee

Beoordeel dit product als eerste

0 stemmen

Praat mee over dit product

Laat hier weten wat jij vindt van de Clarke CBM 240 Waterpomp. Als je een vraag hebt, lees dan eerst zorgvuldig de handleiding door. Een handleiding aanvragen kan via ons contactformulier.

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Clarke CBM 240 Waterpomp. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Clarke. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Clarke CBM 240 Waterpomp in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.