Handleiding Contec CMS50D1 Pulse-oxymeter

Handleiding

7 Operating Guide

7.1 Insert the two batteries properly to the direction, and then replace the cover.

7.2 Open the clip as shown in Figure 5.

Figure 5. Put

finger in

position

7.3 Let the

patient’s finger

put into the

rubber cushions

of the clip

(make sure the

finger is in the

right position),

and then clip the finger.

7.4 Press the switch button once on front panel.

7.5 Do not shake the finger and keep the patient at ease during the process. Meanwhile, human body is not

recommended in movement status.

7.6 Get the information directly from screen display.

7.7 The button has three

functions.When the device is

power off, pressing the button can open it; When the device is power on, pressing the

button shortly can change direction of the screen; When the device is power on,

pressing the button long can change brightness of the screen.

Fingernails and the luminescent tube should be on the same side.

8 Repairing and Maintenance

 Please change the batteries when the low-voltage displayed on the screen.

 Please clean the surface of the device before using. Wipe the device with medical alcohol first, and then

let it dry in air or clean it by dry clean fabric.

 Using the medical alcohol to disinfect the product after use, prevent from cross infection for next time

use.

 Please take out the batteries if the oximeter is not in use for a long time.

 The best storage environment of the device is - 40ºC to 60ºC ambient temperature and not higher than

95% relative humidity.

 Users are advised to calibrate the device termly (or according to the calibrating

program of hospital). It also can be performed at the state-appointed agent or jus

t contact us for calibration.

High-pressure sterilization cannot be used on the device.

Do not immerse the device in liquid.

It is recommended that the device should be kept in a dry environment. Humidity may reduce

the useful life of the device, or even damage it.

9 Troubleshooting

Trouble Possible Reason Solution

The SpO

2

and Pulse

Rate can not be

displayed normally

1. The finger is not properly positioned.

2. The patient’s SpO

2

is too low to be

detected.

1. Place the finger properly and try

again.

2. Try again; Go to a hospital for a

diagnosis if you are sure the device

works all right.

The SpO

2

and Pulse

Rate are not displayed

stably

1. The finger is not placed inside deep

enough.

2. The finger is shaking or the patient is

moving.

1. Place the finger properly and try

again.

2. Let the patient keep calm

The device can not be

turned on

1. The batteries are drained or almost

drained.

2. The batteries are not inserted properly.

3. The malfunction of the device.

1. Change batteries.

2. Reinstall batteries.

3. Please contact the local service

center.

The display is off

suddenly

1. The device will power off

automatically when it gets no signal

within 5 seconds.

2. The batteries are almost drained.

1. Normal.

2. Change batteries.

10 Key of Symbols

Symbol Description

Type BF

Refer to instruction manual/booklet

The pulse oxygen saturation(%)

PRbpm Pulse rate (bpm)

The battery voltage indication is deficient (change the battery in time avoiding the

inexact measure)

1. no finger inserted

2. An indicator of signal inadequacy

battery positive electrode

battery cathode

1.Power switch

2.change direction of the screen

3.Change brightness of the screen

SN Serial number

Alarm inhibit

WEEE (2002/96/EC)

IP22 Ingress of liquids rank

European Representative

This item is compliant with Medical Device Directive 93/42/EEC of June 14,

1993, a directive of the European Economic Community.

11 Function Specification

Display Information Display Mode

The Pulse Oxygen Saturation(SpO

2

) OLED

Pulse Rate(PR) OLED

Pulse Intensity (bar-graph) OLED bar-graph display

Pulse wave OLED

SpO

2

Parameter Specification

Measuring range 0%~100%, (the resolution is 1%).

Accuracy 70%~100%: ±2% ,Below 70% unspecified.

Optical Sensor Red light (wavelength is 660nm)

Infrared (wavelength is 880nm)

Pulse Parameter Specification

Measuring range 30bpm~250bpm (the resolution is 1 bpm)

Accuracy ±2bpm or±2% select larger

Pulse Intensity

Range Continuous bar-graph display, the higher display indicate the

stronger pulse.

Battery Requirement

1.5V (AAA size) alkaline batteries × 2 or rechargeable battery

Battery Useful Life

Two batteries can work continually for 20 hours

Dimensions and Weight

Dimensions 61(L) × 36(W) × 32(H) mm

Weight About 57g (with the batteries)

Appendix

Guidance and manufacture’s declaration-electromagnetic emission

for all EQUIPMENT and SYSTEMS

Guidance and manufacture’s declaration –electromagnetic emission

The CMS50D1 Pulse Oximeter is tended for use in the electromagnetic environment

specified below. The customer of the user of the CMS50D1 Pulse Oximeter should

assure that it isused in such an environment.

Emission test compliance Electromagnetic environment-guidance

RF emissions

CISPR 11

Group 1 The CMS50D1 Pulse Oximeter uses RF

energy only for their internal function.

Therefore, its RF emissions are very low and

are not likely to cause any interference in

nearby electronic equipment.

RF emissions Class B The CMS50D1 Pulse Oximeter is suitable

III

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Contec CMS50D1 Pulse-oxymeter. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Contec. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Contec CMS50D1 Pulse-oxymeter in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Contec Pulse-oxymeters
Meer handleidingen voor Pulse-oxymeters

Beoordeling

Gerelateerde producten

Handleiding

Medisana PM 100 Connect Pulse-oxymeter

Handleiding

Masimo Rad-5v Pulse-oxymeter

Handleiding

Rossmax SB100 Pulse-oxymeter

Handleiding

Homedics PX-130 Pulse-oxymeter

Handleiding

Yuwell YX300 Pulse-oxymeter

Handleiding

Rossmax SB200 Pulse-oxymeter

Handleiding

Yuwell YX302 Pulse-oxymeter

Handleiding

Henry Schein H100B Pulse-oxymeter

Gerelateerde categorieën