Handleiding Fito ASD-10QR Rookmelder

Handleiding

Instruction manual

WIRELESS INTERCONNECTABLE SMOKE ALARM WITH A WITH BUILT-IN 10-YEAR 3V BATTERY

Model: ASD-10QR

IMPORTANT INFORMATION

Correct usage will ensure you have valuable extra

time to escape. Every correctly installed smoke detec-

tor will increase your potential escape time.

• A smoke detector is not a fire-prevention

measure.

• Install the smoke detector in the correct place, if

possible in the middle of the ceiling.

WARNING: Read carefully chapter "Never fit a

smoke detector"

• Keep the smoke detector out of the reach of

children.

• Test the unit on a monthly basis and after a

period of absence. When the alarm does not sound,

have your smoke alarm inspected by the service

point or when the smoke alarm is more than 10

years old discard the alarm.

CAUTION: Never test with fire!

• Clean the detector regularly (once a month) using

the soft brush from a vacuum cleaner. In addition

the smoke alarm can also be cleaned using a moist

cloth.

• If the detector emits a beeping sound every 40

seconds, this means that the battery is nearly flat

and that you should replace the smoke detector.

• The lifespan of smoke detectors is 10 years.

• A false alarm can be silenced by pressing the test

and silence button.

• You can make your Model ASD-10Q smoke detec-

tor less sensitive for 10 ± 2 minutes by

pressing the test button shortly. The detector will

nonetheless sound the alarm if the quantity of

smoke is too significant.

• You can also test and switch on the hush feature by

using the ASD-RRC. This is the optionally available

wireless remote control.

IMPORTANT INFORMATION IN CASE OF

ALARM IN THE EVENT OF A FIRE

• Plan TWO escape routes and practice these with all

members of the family.

• Agree upon a location, where everyone goes to in

case of a fire.

In the event of a fire:

• Leave the building immediately and go to the

agreed location.

• Make sure everyone has left the building.

• Close the doors behind you and never open a warm

door. In case of a warm door, choose a different

escape route.

• In the event of considerable build-up of smoke,

crawl out of the building keeping as close to the

floor as possible.

• Wherever possible, breathe through a cloth (prefera-

bly moist), or else hold your breath as much as you

can. The majority of deaths and injuries are caused

by smoke inhalation rather than fire itself.

• Call the fire brigade outside or at the neighbours.

• NEVER go back into a burning building.

• Additional information can be obtained at the local

fire department.

SPECIFICATIONS:

RF frequency: 868.100 (<1% duty cycle)

RF Codes: 65535

RF Power: +14 dBm max

5)UDQJH PPLQRSHQ¿HOG

Battery life: 10 years under normal

conditions

Battery type: Sealed, Lithium, AA, 3V

&RQVXPSWLRQ ȺVWDQGE\

 P$LQDODUP

Operating temperature: 0ºC tot + 55ºC

2SHUDWLQJKXPLGLW\ 5+DW&

Alarm sound level: >85dB op 3 meter

Hush time: 10 ± 2min.

&HUWL¿FDWLRQV (1&(5('

POSITIONING THE SMOKE DETECTOR

RECOMMENDED LOCATIONS:

Optimal protection:

In all occupied areas such as bedrooms, living room,

study and the escape route as hallway, basement

and attic.

Maximum protection:

- Smoke detector in all rooms (with the exception

of bathrooms, kitchen, garages, etc.)

- Heat detectors can be installed in bathrooms,

kitchens, airing cupboards, utility rooms, etc.

ZLWKLQPHWUHVRIDSRWHQWLDOVRXUFHRI¿UH

• The smoke detector should preferably be installed

in the middle of the ceiling, at least 50 cm from the

wall.

• In the case of pitched roofs, install the smoke detec-

WRURQWKHVORSLQJZDOODWOHDVWFP

(measured vertically) from the ridge of the roof.

• Ensure that the detector can always be reached for

testing and cleaning.

Never fit a smoke alarm:

• In bathrooms, kitchens, shower rooms, garages,

etc. Places where a smoke detector may go off

needlessly due to condensation, normal smoke or

gases. A smoke detector should be fitted at least 5

metres from such sources of smoke.

3ODFHVZKHUHWKHWHPSHUDWXUHPD\H[FHHG&RU

IDOOEHORZ&HJDWWLFVMXVWDERYHDILUH

place, etc.

• In the vicinity of (or adjacent to) decorative objects,

doors, sockets, lights, fittings, windows, wall

ventilators, etc. which could mean that smoke does

not reach the smoke detector. Minimum 50cm

away.

• Surfaces that are usually warmer or colder than the

rest of the room. Differences in temperature can

prevent smoke from reaching the detector.

• Adjacent to or directly above stoves or heaters.

• In very high or difficult to reach places. This makes

it hard to reach the detector to test or clean it.

• In very dusty or dirty places. Accumulation of dust

will prevent smoke from reaching the smoke cham-

ber and in time will lead to a false alarm.

• Within 1 metre of dimmer switches and wiring. Some

dimmer switches can trigger a fault in the detector.

• Within 1.5 metres of fluorescent lights. Electrical

impulses can adversely affect the functioning of the

detector.

• Outdoors and in spaces where a large number of in-

sects are found. Small insects in the unit’s detection

chamber can disrupt the functioning of the detector.

The labels on the rear side of the detector contain

important information.

HOW TO USE THE ASD-10QR:

Wireless interconnecting the smoke alarms:

The ASD-10QR is a wireless device. Each smoke

alarm can be the sender or the receiver.

To interconnect a few smoke alarms the unique RF

code must be generated in one of them and set to

the others All ASD-10QR smoke alarms in a house,

apartment or property should be set to the same RF

Code.

It is not recommended to interconnect more than 24

smoke alarms.

Generating the unique RF Code:

• Remove all smoke alarms from bases.

• Press and hold the test button for about 4 sec. on

one of them (randomly chosen) and release the

button when the red LED will lit. This smoke alarm

(Master) has chosen one of the 65.535 possible RF

codes. The red LED on the Master will be lit until

the interconnect procedure is over.

• In order to set the generated code to the other

smoke alarms(Slaves) push the Test button on

each of them. The successful setting of the code to

the Slave will be accompanied with blinking of the

red LED. You have two minutes to inter connect all

smoke alarms, after two minutes the red LED will

extinguish indicating that the interconnect proce-

dure has ended.

• To end the interconnect procedure you can also

press the test button on the Master or fasten the

Master on to the base. The red LED will extinguish

indicating that the interconnect procedure has

ended.

How to disconnect a smoke alarm:

If you need to disconnect one smoke alarm carry out

Generating the unique RF Code procedure.

How to add a smoke alarm:

To add a smoke alarm you need to carry out the Ge-

nerating the unique RF Code procedure on all the

smoke alarms you want to interconnect.

Testing the smoke alarms and the interconnec-

tion:

Install all interconnected smoke alarms to bases.

Press and hold on the Test button on one of them

(Test mode). After the period of 10 to 30 sec. all

interlinked smoke alarms will go to the Remote Alarm

mode. Upon releasing the Test button, the other

alarms will stay in the Remote Alarm for 5-10 sec.

The installation:

1. Choose a location that satisfies the conditions as

described in: Positioning the smoke detector.

2. Remove the base plate of the detector by turning

the base plate anticlockwise (to the left).

3. Mark the mounting holes in the base plate and

drill the holes (use a 6 mm drill). If you do not

use the dowels, then use a 3 mm drill. Screw the

base plate securely onto the ceiling. Make sure

that the base plate is tight

against the ceiling so that

no air circulation above the

smoke alarm is possible,

which could impede smoke

detection.

If the opening is too large,

this must be remedied by

the use of a fille

r.

If you use the double sided

tape, make sure the base

and the surface you want

to install the smoke alarm

is grease free. Attach the double sided tape to the

base and then the base to the ceiling.

4. Place the smoke detector on the base and turn it

until the smoke detector clicks into the base. Turn

the smoke detector clockwise to secure the smoke

detector and activate it. A melody will sound to

confirm the activation.

5. Test your smoke alarms by following the

procedure as described in chapter: "Testing

the smoke alarms and the interconnection"

ATTENTION: The smoke alarm should be covered

or temporarily removed during renovation work or

structural alterations. Once the day’s work is com-

plete, clean the smoke detector with the soft brush

from a vacuum cleaner and then activate it again.

Always test it by pressing the test button once it has

been reinstalled.

WARNING: covering the smoke alarm causes loses

its functionality.

WARNING: Do not paint the smoke alarm. Also

QHYHUWHVWWKHVPRNHDODUPZLWK¿UHRUVLJDUHWWHV

CAUSES OF FALSE ALARM

The smoke detector can be activated by steam, con-

densation, dust, smoke and small insects. These are

to be prevented as much as possible. See chapter

"Never fit a smoke alarm". If a smoke alarm fre-

quently gives a false alarm, it might be necessary to

install the detector in another location.

Additional information can be found on our website

ZZZ¿WRQO)$4:KHQDVPRNHDODUPGRHVQRWIXQF-

tioning correctly, contact your supplier or

)LWR3URGXFWV%9ZZZ¿WRQO

MAINTENANCE

•

Test your smoke alarm regularly, once a month and

always after a period of absence. See "

Testing the

smoke alarms and the interconnection"

• Clean the detector regularly (once a month) using

the soft brush from a vacuum cleaner. In addition

the smoke alarm can also be cleaned using a moist

cloth.

• Never allow the detector to come into contact with

ÀXLGV

LIMITATIONS OF SMOKE DETECTORS

In countries where they are commonly in use, smoke

detectors have contributed to reducing deaths and

injuries. Independent bodies have established that

they were insufficient in around 35% of fires, namely

in the following situations:

• Where the battery had been removed or was not

working. For that reason, you should test the unit

regularly.

• Where smoke is not able to reach the detector in

the event of a fire, meaning the unit cannot be set

off. Examples include a fire on another floor where

there is no smoke detector, a fire behind closed

doors, a fire in a chimney or smoke being blown

away from the detector. For that reason, smoke

detectors are recommended in all rooms, or at any

rate on every floor.

• Where the alarm is not heard. A person may not be

woken by the alarm if that person had consumed

excess alcohol and/or drugs.

• A few fires are not always detected on time, e.g.

smoking in bed, if there is no smoke detector in the

bedroom. In the case of escaping from gas or

violent explosions, improperly storing explosive pro-

ducts and flammable liquids (petrol, paint, methyla-

ted spirit, etc.), electrical faults, acids, children

playing with matches (fire).

• The lifespan of smoke detectors is 10 years.

PRODUCT WARRANTY

If used and maintained properly, the manufacturer

guarantees this product against material and/or

manufacturing defects for a period of 5 years from the

original date of purchase. Exceptions include damage

arising from accidents or misuse. If the product beco-

mes defective within the stated period, then it will be

repaired or replaced free of charge. Please do not

open the smoke alarm or attempt to repair the pro-

duct yourself or tinker with it, which will invalidate the

warranty.

WARNING: Unscrewing the smoke alarm invalidates

the warranty.

DOP (Declaration of Performance)

The DoP can be downloaded on our website www.

fito.eu

INSTRUCTIONS FOR REMOVAL

Do not dispose of your old detector in

the bin, but rather hand it in to a local col-

lection point for small, domestic waste.

EUROPEAN PRODUCT

EUROPEAN SUPPLIER:

Fito Products BV

Molenvliet 22

09

WIJK BIJ DUURSTEDE

Nederland

[email protected] - www.fito.eu

Base

Mounting holes:

SAFETY ISSUES:

•

Do not paint to the smoke alarm and do not cover it.

• Never install smoke detectors in rooms with a high humidity, such

as bathrooms, showers, kitchens and saunas.

• Test your smoke alarm regularly, once a month and always after

a period of absence. Test by pressing the test button for at least 2

seconds, a loud alarm will follow. Keep a distance of at least 50 cm.

between the alarm and your ears.

• Never open the smoke alarm, this will invalidate the warranty.

• Do not test with smoke directly after instalation, wait at least 1 hour.

figure 4

red LED

Test/hush

button

kitchen

living room

bathroom

bedroom

hallway

figure 1

bedroom

bedroom

bedroom

bedroom bedroomhallway

kitchen hallway

living room

Basement

figure 2

RETAIN THESE INSTRUCTIONS FOR FUTURE USE!

These instructions contain important information for correct instal-

lation and use of your smoke detector. Please read this informa-

tion carefully and retain these instructions for future

reference.

Sound signal: Red LED: Function:

No signal Flashes every

320 sec.

Standby mode

Periodical automatic self-diagnostics

Long pulsating sound Flashes every

0.5 sec.

Alarm status

Long lingering sound Non 1 of the interconnected smoke alarms are in alarm

1 short signal every 40 sec. Non Low battery signal. The smoke alarm needs to be

replaced.

2 short signals every 4 hour Non Low battery signal in one of the interconnected smoke

alarms. This smoke alarm needs to be replaced.

3 short signals every 40 sec. Non Fault/ smoke chamber contamination

No signal Flashes every

0.5 sec.

The smoke chamber has been abruptly contaminated

and needs to be cleaned.

No signal Flashes every

10 sec.

HUSH mode (Alarm muting, sensitivity reduction)

Long pulsating sound while

pressing the test button.

Flashes every

0.5 sec.

Test mode: De smoke alarm is operates correctly. All

interconnected and installed to the base smoke alarms

will go to Remote Alarm status in 10 - 30 sec.

3 short signals while pressing

the test button.

Flashes every

3 sec.

De smoke alarm does not operate correctly and needs

to be replaced.

• When the ASD-10QR is removed from the base (disconnected) after detecting a problem, it gives the

sound that belongs to the detected problem.

• The remaining connected ASD-QR smoke alarms will sound two beeps on disconnection (removal from

base), up to 4 hours after removal of the ASD-10QR with a battery empty indication.

FUNCTION AND MEANING OF LIGHT AND SOUND SIGNALS:

versie 1 2018-5

1134

EN14604:2005/AC 2008

Essential characteristics: Performance:

Nominal activation conditions/sensitivity, response delay (response

WLPHDQGSHUIRUPDQFHXQGHU¿UHFRQGLWLRQV

Passed

Fito Products BV

Molenvliet 22

09:LMNELM'XXUVWHGH

The Netherlands

17

&35

Operational reliability: Passed

Tolerance to supply voltage: Passed

Durability of operational reliability and response delay, temperature

resistance:

Passed

Durability of operational reliability, vibration resistance: Passed

Optical smoke detector,

alerts you in the event

RI¿UHRUVPRNHDQGLV

suitable for residential

buildings.

Durability of operational reliability, humidity resistance: Passed

Durability of operational reliability, corrosion resistance: Passed

Durability of operational reliability, electrical stability: Passed

&KDUDFWHULVWLFVFHUWL¿HGE\$13,

Ceiling mount YES

Battery powered YES

Battery lifetime 10 years YES

Individual Alarm Indicator YES

Alarm silence facility YES

Suitable for installation in a

caravan

NO

Wireless interconnectable up

to 24 pcs.

YES

EN14604:2005/AC 2008

vfdb 14/01

1134-CPR-199

DoP no: 10QR16

RED

17

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Fito ASD-10QR Rookmelder. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Fito. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Fito ASD-10QR Rookmelder in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Fito Rookmelders
Meer handleidingen voor Rookmelders

Veelgestelde vragen over Fito ASD-10QR Rookmelder

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Fito ASD-5 Rookmelder

Handleiding

Fito ASD-10 Rookmelder

Handleiding

Fito ASD-10Q Rookmelder

Handleiding

First Alert Onelink Rookmelder

Handleiding

Ei Electronics Ei181 Rookmelder

Handleiding

Nedis DTCTSC10WT Rookmelder

Handleiding

FireX PG240C Rookmelder

Handleiding

IKEA VAKTA Rookmelder

Gerelateerde categorieën