Handleiding Makita BUH550 Heggenschaar

Handleiding

9

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before adjusting or

checking function on the tool.

Installing or removing battery cartridge

CAUTION:

• Hold the tool and the battery cartridge firmly when

installing or removing battery cartridge. Failure to

hold the tool and the battery cartridge firmly may cause

them to slip off your hands and result in damage to the

tool and battery cartridge and a personal injury. (Fig. 1)

• Always switch off the tool before insertion or removal of

the battery cartridge.

• To remove the battery cartridge, withdraw it from the

tool while sliding the button on the front of the cartridge.

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If you can see the red part on

the upper side of the button, it is not locked completely.

Insert it fully until the red part cannot be seen. If not, it

may accidentally fall out of the tool, causing injury to

you or someone around you.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Battery protection system

The battery cartridge is equipped with the protection

system, which automatically cuts off the output power for

its long service life.

The tool may stop during operation when the tool and/or

battery are placed under the following situation. This is

caused by the activation of protection system and does

not show the tool trouble.

• When the tool is overloaded:

At this time, release the switch trigger and remove

causes of overload and then pull the switch trigger

again to restart. When the tool does not work even

after pulling the switch trigger, the battery power auto-

stop is still at work. Charge the battery cartridge before

use.

• When the remaining battery capacity becomes low:

Recharge the battery cartridge.

Handle mounting positions (Fig. 2)

The handle can be rotated to either 90° left or right and

mounted either 45° or 90° position to fit your work needs.

First, pull the knob and rotate the handle clockwise or

counterclockwise in the direction of arrow as shown in the

figure. The handle will be locked in 45° position. The pull

the knob and rotate more. The handle will be locked in 90°

position.

CAUTION:

• Always make sure that the handle is locked in the

desired position before operation.

Switch action

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the “OFF” position when

released. (Fig. 3)

For your safety, this tool is equipped with a dual switching

system. To turn on the tool, press triggers A and B.

Release either one of the two pressed triggers to turn off.

The sequence of switching is unimportant as the tool only

starts when both switches are activated.

Speed change (Fig. 4)

The strokes per minute can be adjusted just by turning the

adjusting dial. This can be done even while the tool is

running. The dial is marked 1 (lowest speed) to 6 (full

speed).

Refer to the table below for the relationship between the

number settings on the adjusting dial and the strokes per

minute.

CAUTION:

• The speed adjusting dial can be turned only as far as 6

and back to 1. Do not force it past 6 or 1, or the speed

adjusting function may no longer work.

• The strokes per minute vary by the conditions of

battery cartridge and shear blades.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out any

work on the tool.

Battery adapter (Accessory) (Fig. 5 & 6)

CAUTION:

• Before using battery adapter, read all instructions on

tools using battery.

• When charging a battery cartridge, first remove it from

the battery adapter and then charge it. It is not allowed

to charge the battery cartridge while using battery

adapter.

Installing or removing battery adapter

• Always switch off the tool before insertion or removal of

the battery adapter.

• To remove the battery adapter, withdraw it from the tool

while sliding the button on the adapter.

• To insert the battery adapter, align the tongue on the

battery adapter with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If you can see the red part on

the upper side of the button, it is not locked completely.

Number on adjusting dial Strokes per minute (min

-1

)

6 1,800

5 1,750

4 1,650

3 1,500

2 1,300

1 1,000

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Makita BUH550 Heggenschaar. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Makita. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Makita BUH550 Heggenschaar in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Makita Heggenscharen
Meer handleidingen voor Heggenscharen

Veelgestelde vragen over Makita BUH550 Heggenschaar

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Makita DUM604PT4J Heggenschaar

Handleiding

Makita UH004GZ Heggenschaar

Handleiding

Makita UH008GZ Heggenschaar

Handleiding

Makita DUH501RTE Heggenschaar

Handleiding

Makita UH005GZ Heggenschaar

Handleiding

Makita UH6570 Heggenschaar

Handleiding

Makita UH008GM201 Heggenschaar

Handleiding

Makita DUH523 Heggenschaar

Gerelateerde categorieën