Handleiding Makita PLM4622N2 Grasmaaier

Handleiding

13

10-2 CUTTING BLADE

CAUTION: Be sure to disconnect and ground the

spark plug wire before working on the cutting blade to

prevent accidental engine starting. Protect hands by using

heavy gloves or a rag to grasp the cutting blades.

Tip mower as specified in separate engine manual.

Remove the hex bolt and washer which hold the blade

and blade adapter to the engine crankshaft. Remove the

blade and adapter from the crankshaft.

WARNING: Periodically inspect the blade

adapter for cracks, especially if you strike a foreign object.

Replace when necessary.

For best results your blade should be sharp. The blade

may be resharpened by removing it and either grinding or

filing the cutting edge keeping as close to the original

bevel as possible. It is extremely important that each

cutting edge receives an equal amount of grinding to

prevent an unbalanced blade. Improper blade balance will

result in excessive vibration causing eventual damage to

the engine and mower. Be sure to carefully balance blade

after sharpening. The blade can be tested for balance by

balancing it on a round shaft screwdriver. Remove metal

from the heavy side until it balances evenly. (Fig. 25)

Before reassembling the blade and the blade adapter to

the unit, lubricate the engine crankshaft and the inner

surface of the blade adapter with light oil. Install the blade

adapter on the crankshaft with the “star” away from the

engine. Refer to Fig. 25. Place the blade with the part

number facing away from the adapter. Align the washer

over the blade and insert the hex bolt. Tighten the hex bolt

to the torque listed below.

10-3 BLADE MOUNTING TORQUE

Center Bolt must be tightened to 35 - 45 Nm torque. To

insure safe operation of your unit. ALL nuts and bolts must

be checked periodically for correct tightness. After

prolonged use, especially in sandy soil conditions, the

blade will become worn and lose some of the original

shape. Cutting efficiently will be reduced and the blade

should be replaced.

Replace with an approved factory replacement blade only.

Possible damage resulting from blade unbalance

condition is not the responsibility of the manufacturer.

When you change the blade, must use the original type

marked on the blade (MAKITA 263001451) (for order the

blade, pls. contact your local dealer or call our company).

WARNING: Do not touch rotating blade.

10-4 ENGINE

Refer to the separate engine manual for engine

maintenance instructions.

Maintain engine oil as instructed in the separate engine

manual packed with your unit.

Read and follow instructions carefully.

Service air cleaner as per separate engine manual under

normal conditions. Clean every few hours under extremely

dusty conditions. Poor engine performance and flooding

usually indicates that the air cleaner should be serviced.

To service the air cleaner, refer to the separate engine

manual packed with your unit.

The spark plug should be cleaned and the gap reset once

a season. Spark plug replacement is recommended at the

start of each mowing season; check engine manual for

correct plug type and gap specifications.

Clean the engine regularly with a cloth or brush. Keep the

cooling system (blower housing area) clean to permit

proper air circulation which is essential to engine

performance and life. Be certain to remove all grass, dirt

and combustible debris from muffler area.

11. STORAGE INSTRUCTIONS

(OFF SEASON)

The following steps should be taken to prepare lawn

mower for storage.

1. Empty the tank after the last mowing of the season.

a) Empty the petrol tank with a suction pump.

CAUTION: Do not drain the petrol in closed

rooms, in close proximity of open fire, etc. Do not smoke!

Petrol fumes can cause explosion or fire.

b) Start the engine and let it run until it has used up

all remaining petrol and stalls.

c) Remove the spark plug. Use an oilcan to fill

approx. 20 ml oil into the combustion chamber.

Operate the starter to evenly distribute the oil in

the combustion chamber. Replace the spark plug.

2. Clean and grease the lawn mower carefully as

described above under “LUBRICATION

INSTRUCTIONS”.

3. Slightly grease the cutter to avoid corrosion.

4. Store the lawn mower in a dry, clean and frost-

protected place, out of reach of unauthorized persons.

CAUTION: The engine must have completely

cooled down before storing the lawn mower.

NOTE:

- When storing any type of power equipment in an

unventilated or material storage shed;

- Care should be taken to rust-proof the equipment.

Using a light oil or silicone, coat the equipment,

especially cables and all moving parts.

- Be careful not to bend or kink cables.

- If the starter rope becomes disconnected from rope

guide on handle, disconnect and ground the spark plug

wire, Depress the blade control handle and pull the

starter rope out from engine slowly. Slip the starter rope

into the rope guide bolt on handle.

Transport

Turn the engine off and allow the engine to cool down.

Then disconnect the spark plug wire and empty the fuel

tank according to the instructions in the engine manual.

Ensure not to bend or damage the cutter when pushing

the lawn mower over obstacles.

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Makita PLM4622N2 Grasmaaier. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Makita. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Makita PLM4622N2 Grasmaaier in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Makita Grasmaaiers
Meer handleidingen voor Grasmaaiers

Veelgestelde vragen over Makita PLM4622N2 Grasmaaier

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Makita PLM5600N2 Grasmaaier

Handleiding

Makita DLM462 Grasmaaier

Handleiding

Makita PLM4621N2 Grasmaaier

Handleiding

Makita BLM381 Grasmaaier

Handleiding

Makita DLM532 Grasmaaier

Handleiding

Makita PLM5130 Grasmaaier

Handleiding

Makita ELM4110 Grasmaaier

Handleiding

Makita LM001CT4X4 Grasmaaier

Gerelateerde categorieën