Handleiding Troy-Bilt TB4516CC Kettingzaag

Handleiding

17

Sprocket Tip Lubrication

The Lube Gun (optional) is recommended for applying

grease to the guide bar sprocket tip. The Lube Gun is

equipped with a needle nose tip which is necessary for

the efficient application of grease to the sprocket tip.

The sprocket tip on

your new saw has

been pre-lubricated at the factory. Failure to

lubricate the guide bar sprocket tip as

explained below will result in poor

performance and seizure, voiding the

manufacturer’s warranty.

Lubrication of the sprocket tip is

recommended after each saw use. Always

thoroughly clean guide bar sprocket tip

before lubrication.

CAUTION:

Fig. 28

To lubricate the sprocket tip:

1. Unplug the chain saw from the power source.

NOTE: It is not necessary to remove the saw chain to

lubricate the guide bar sprocket tip. Lubrication

can be done on the job.

2. Clean the guide bar sprocket tip.

3. Using the Lube Gun (optional), insert tip of lube gun

into the lubrication hole and inject grease until it

appears at outside edge of sprocket tip (Fig. 32).

4. Make sure that the Chain Brake® is deactivated.

Rotate saw chain by hand. Repeat lubrication

procedure until the entire sprocket tip has been

greased.

GUIDE BAR MAINTENANCE

Frequent lubrication of the guide bar is required. Proper

maintenance of the guide bar, as explained in this

section, is essential to keep your saw in good working

condition.

MAINTENANCE AND REPAIR INSTRUCTIONS

Ensure that the

power cord is

disconnected before performing any

maintenance on your saw.

WARNING:

Always use

protective gloves

when handling the saw chain.

WARNING:

Maintenance Procedures

Most guide bar problems can be prevented merely by

keeping the chain saw well maintained. Incorrect filing

and non-uniform cutter and depth gauge settings cause

most guide bar problems, primarily resulting in uneven

bar wear. As the bar wears unevenly, the rails widen,

which may cause chain clatter and difficulty in making

straight cuts.

Insufficient guide bar lubrication and operating the saw

with chain that is too tight will contribute to rapid bar wear.

To help minimize bar wear, the following guide bar

maintenance procedures are recommended:

BAR WEAR - Turn guide bar frequently at regular

intervals (for example, after 5 hours of use), to ensure

even wear on top and bottom of bar.

BAR GROOVES - Bar grooves (or rails which support and

carry the chain) should be cleaned if saw has been used

heavily or if saw chain appears dirty. Rails should always

be cleaned every time saw chain is removed.

OIL PASSAGES - Oil passages on the bar should be

cleaned to ensure proper lubrication of the bar and chain

during operation. This can be done using a soft wire

small enough to insert into the oil discharge hole.

NOTE: The condition of the oil passages can be easily

checked. If the passages are clear, the chain will

automatically give off a spray of oil within

seconds of starting the saw. Your saw is

equipped with an automatic oiler system.

Cleaning Bar Rails

1. Remove sprocket cover, bar and chain. Refer to the

Saw Chain Tension Adjustment section.

2. Using a screwdriver, putty knife, wire brush or other

similar instrument, clear residue from the rails on the

guide bar. This will keep the oil passages open to

provide proper lubrication to the bar and chain (Fig. 29).

3. Reinstall the bar, chain, sprocket cover and bar bolt

knob. See Section Install the Guide Bar / Saw Chain

for more information.

Fig. 29

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Troy-Bilt TB4516CC Kettingzaag. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Troy-Bilt. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Troy-Bilt TB4516CC Kettingzaag in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Troy-Bilt Kettingzagen
Meer handleidingen voor Kettingzagen

Veelgestelde vragen over Troy-Bilt TB4516CC Kettingzaag

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Beoordeling

Gerelateerde producten

Handleiding

Troy-Bilt TB4218CC Kettingzaag

Handleiding

Troy-Bilt TB4920CC Kettingzaag

Handleiding

Troy-Bilt TB4016CC Kettingzaag

Handleiding

Troy-Bilt TB4620CC Kettingzaag

Handleiding

Troy-Bilt TB3516 Kettingzaag

Handleiding

Stihl GTA 26 Kettingzaag

Handleiding

Parkside IAN 327520 Kettingzaag

Handleiding

Greencut OH650X Kettingzaag

Gerelateerde categorieën