Handleiding Bikemate 22967 Fietscomputer

Handleiding

Dok./Rev.-Nr. 195787_20180117

A

6

5

4

3

2

1

7

8

9

10

11

12

13

B

6

5

13

C

11

12

13

D

2 mm max.

7

11

8

E

14

10

11

F

11

1

G

5 1

H

User Manual

ID: #07177

m

y

h

a

n

s

e

c

o

n

t

r

o

l

.

c

o

m

C

E

R

T

I

F

I

E

D

User-friendly

Manual

DISTRIBUTED BY:

ALDI INC., BATAVIA, IL 60510

WWW.ALDI.US

USA

MODEL:

22967

service@801service.net

866-558-8096

AFTER SALES SUPPORT

USA

95698

05/2018

WIRELESS BICYCLE

COMPUTER

YEAR

WARRANTY

3

General information

Reading and storing the

user manual

This user manual ac-

companies this wireless

solar bicycle computer.

It contains important

information about

start-up and use.

Before using the bicycle comput-

er, read the user manual carefully.

This particularly applies to the

safety instructions. Failure to fol-

low this user manual may result

in severe injury, or damage to the

bicycle computer. Store the user

manual for further use. If you pass

the bicycle computer on to third

parties, please be absolutely sure

to include this user manual.

Explanation of symbols

The following symbols and signal

words are used in this user man-

ual, on the bicycle computer or on

the packaging.

WARNING!

This signal symbol/word desig-

nates a hazard with moderate

degree of risk which may lead

to death or severe injury if not

avoided.

NOTICE!

This signal word warns against

potential damages to property.

This symbol pro-

vides you with use-

ful supplementary

information about

assembly or use.

FCC Conformity

This bicycle computer complies

with part 15 of the FCC rules. Op-

eration is subject to the following

two conditions: (1) This device

may not cause harmful interfer-

ence, and (2) this device must

accept any interference received,

including interference that may

cause undesired operation.

Please take attention that chang-

es or modification not expressly

approved by the party responsi-

ble for compliance could void the

user’s authority to operate the

equipment.

The operating frequency is be-

tween 120kHz and 125kHz.

Safety

Proper use

The bicycle computer is designed

exclusively for displaying and col-

lecting information when using

a bicycle. It is only intended for

private use and not suitable for

commercial purposes.

Only use the bicycle computer

as described in this user manu-

al. Using it in any other way is

deemed improper and may result

in damage to property or even

personal injury. The bicycle com-

puter is not a children’s toy.

The manufacturer or vendor

accepts no liability for damage

caused by improper or incorrect

use.

Package contents/

device parts

1

Bicycle computer (example)

2

Display

3

Right button

4

Left button

5

Bicycle computer mounting

bracket

6

Rubber pad (bicycle

computer)

7

Magnet

8

Magnet holder

9

CR2016 battery

10

CR2032 battery

11

Sensor

12

Rubber pad (sensor)

13

Cable ties, 6×

14

Battery compartment cover

Safety instructions

WARNING!

Danger for children and per-

sons with impaired physical,

sensory or mental capaci-

ties (e.g. partially disabled

persons, older persons with

reduced physical and mental

capacities) or lack of experi-

ence and knowledge (e.g.

older children).

− This bicycle computer may

be used by children ages

eight and over as well as

persons with impaired

physical, sensory or

mental capacities or those

lacking experience and

knowledge, if they are

supervised or have been

instructed in how to safely

use the bicycle computer

and understand the risks

associated with operating

it. Children must not play

with the bicycle computer.

Cleaning and user mainte-

nance must not be per-

formed by unsupervised

children.

− Keep children under eight

years of age away from the

bicycle computer.

WARNING!

Danger of suffocation!

The bicycle computer contains

small parts. Children could

swallow them when playing

and choke.

− Keep small parts away from

children.

WARNING!

Battery hazards!

The bicycle computer and the

sensor each contain a battery.

Improper handling of the bat-

teries may result in explosion or

serious internal injury.

− Store both new and used

batteries so that they are

not accessible to children.

− If you suspect that a battery

has been swallowed or

otherwise incorporated,

promptly consult a physi-

cian.

− Only replace the batteries

with the same battery type.

− Do not touch leaky bat-

teries. If you do come into

contact with battery acid,

wash the affected area

thoroughly and rinse it with

plenty of water. If leaked

battery acid comes into

contact with your eyes or

causes skin irritation, also

seek medical attention.

− If it is no longer possible to

securely close the battery

compartment, dispose of

the bicycle computer as

described in the chapter

“Disposal”.

− Do not charge or reactivate

batteries, do not disassem-

ble them, do not throw

them in fire and do not

short circuit them.

− Dispose of batteries at your

local collection point.

NOTICE!

Risk of damage!

− Improper handling of the

bicycle computer may

result in damage to the

bicycle computer.

− You can use the bicycle

computer at ambient

temperatures between

14°F and 122°F (-10°C and

+50°C).

− Do not expose the bicycle

computer to permanent

moisture.

− Avoid dust, heat and con-

tinuous exposure to direct

sunlight.

− Never try to repair the bicy-

cle computer yourself. For

technical problems, contact

the service address indicat-

ed on the warranty card.

Information about

solar cells

This bicycle computer is equipped

with solar cells that transform

light energy into electricity. This

extends the useful life of the

battery. However, batteries are

needed for the sensor and also to

supply energy when it is dark.

Checking the bicycle

computer

1. Take the bicycle computer

1

out of the packaging.

2. Remove the protective foil

from the bicycle computer.

3. Check to make sure the bicy-

cle computer is complete and

undamaged (see Fig.A).

If it is not, do not use the

bicycle computer. Contact the

service address indicated on

the warranty card.

Assembly

Assembling the bicycle

computer mounting

bracket and bicycle com-

puter

1. Attach the bicycle computer

mounting bracket

5

and the

rubber pad

6

to the handle-

bar with two cable ties

13

.

There are two options:

• If you attach the bicycle com-

puter mounting bracket to the

handlebar tube, thread the

cable ties vertically from the

front (see Fig.B, bottom).

• If you attach the bicycle com-

puter mounting bracket to the

stem of the handlebar, thread

the cable ties horizontally

from the side

(see Fig.B, middle).

2. Slide the bicycle computer

1

from the front into the bicycle

computer mounting bracket

until it clicks into place

(see Fig.G).

3. Turn the bicycle computer so

that it is at a 90° angle to the

sensor

11

.

Assembling the sensor

and magnet

1. Attach the sensor

11

and the

rubber pad

12

to the middle

of the fork with two cable

ties

13

(see Fig.C).

Make sure that the

bicycle computer

and the sensor are

at a 90° angle to one

another. The dis-

tance between the bicycle com-

puter and the sensor should be

no more than max. 23" (60cm)

(see Fig.F).

2. Unscrew the magnet

7

and

the magnet holder

8

.

3. Attach the magnet to a spoke

on the front wheel and screw

the magnet holder onto the

magnet (see Fig.D).

Ensure that the

magnet passes the

sensor at a distance

of approx. 0.08"

(2mm) at the arrow

mark on the sensor (see Fig.D).

Start-up

Switching on the bicycle

computer

Before starting the bicycle com-

puter, a few settings must be

made.

− To switch on the bicycle com-

puter

1

, press one of the

two buttons

3

or

4

on the

bicycle computer.

Selecting kilometers/

miles

The selection for the units of

measure kilometers (KM/H) or

miles (MPH) will appear as the

first indicator.

− Press the right button

3

to

switch between the units of

measure.

− Confirm your selection by

pressing the left button

4

.

Setting tire circumference

Necessary after new

battery insertion or

reboot.

How to determine

the tire circumference:

1. Turn the front tire valve to the

lowest position and mark the

position of the valve on the

floor.

2. Move the bicycle forward for

one front wheel revolution

until the valve has returned to

the lowest position.

3. Measure the distance covered

in inches.

This is the tire circumference.

The display shows the default

setting for a “2155” tire circumfer-

ence (=mm). The thousands digit

2 flashes. The thousands digit can

be set to either 1 or 2. The remain-

ing numbers can assume a value

between 0–9.

− Press the right button

3

until the correct number

appears.

The thousands digit is set.

− Confirm your entry by pressing

the left button

4

.

− Repeat the steps for the hun-

dreds, tens and ones.

Setting the total distance

The display shows the default

setting for a total distance of

“00000”.

− Press the right button

3

to

increase the number by one.

− Confirm your entry by pressing

the left button

4

.

The ones, tens, hundreds, thou-

sands and ten thousands can as-

sume a value between 0–9.

Setting the inspection

interval

The display will show the default

setting of “000.00” for the total

distance. This corresponds to the

remaining distance until the next

bike inspection.

− Press the right button

3

to increase the ones, tens or

hundreds by one.

− Confirm your entry by pressing

the left button

4

.

Setting weight

The display will show a default

setting of “065” for weight.

− Press the right button

3

to

increase the hundreds, tens or

ones by one.

− Confirm your entry by pressing

the left button

4

.

Setting the CO₂ savings

This function calculates the CO₂

savings. This determines how

much CO₂ would have been

produced if the journey had

been made by car rather than

by bicycle. Look in the technical

documents of your car to find its

emissions value in g/km. Or use

the default setting of 160 g/km.

The default value of “160” appears.

− Press the right button

3

to

increase the hundreds, tens or

ones by one.

− Confirm your entry by pressing

the left button

4

.

Setting the time

The hour display flashes.

− Press the right button

3

until the correct number

appears.

The hour display is set.

− Confirm your entry by pressing

the left button

4

.

zur Freigabe/Korrektur_V8

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Bikemate 22967 Fietscomputer. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Bikemate. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Bikemate 22967 Fietscomputer in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Bikemate Fietscomputers
Meer handleidingen voor Fietscomputers

Veelgestelde vragen over Bikemate 22967 Fietscomputer

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Bikemate 22975 Fietscomputer

Handleiding

Bikemate MCP 30102 Fietscomputer

Handleiding

Bikemate 22970 Fietscomputer

Handleiding

Bikemate T52432 Fietscomputer

Handleiding

Bikemate E83005 Fietscomputer

Handleiding

Sigma BC 23.16 STS Fietscomputer

Handleiding

Blackburn Atom SL 3.0 Fietscomputer

Handleiding

Pro Scio Alti Fietscomputer

Gerelateerde categorieën