Handleiding Vtech VM3261 Babyfoon

Handleiding

Congratulations

on purchasing your new VTech product. Before

using this product, please read Important

safety instructions.

This manual has all the feature operations

and troubleshooting necessary to install and

operate your new VTech product. Please

review this manual thoroughly to ensure proper

installation and operation of this innovative and

feature rich VTech product.

For support, shopping, and everything new at

VTech, visit our website at

www.vtechphones.com.

What’s in the box

Strangulation

Hazard

Keep this cord out of reach of children.

The cord needs to be at least three feet

away from the child at all times. Do not

use with an extension cord. Do not

remove this tag.

Éloignez ce cordon des enfants. Le

cordon doit se trouver à au moins trois

pieds d’un enfant et ce, en tout temps.

N’utilisez pas de rallonge. Ne retirez pas

cette étiquette.

Mantenga este cable fuera de la alcance

de los niños. Este cable debe estar por

lo menos tres pies fuera de la alcance

del niño en todo momento. No lo use

con una extensión inalámbrica. No quite

esta etiqueta.

Risque

d’étranglement

Riesgo de

estrangulación

＜1m (3ft)

＞1m (3ft)

Install the battery

The parent unit runs on rechargeable battery

or AC power. To continuously monitor your

baby, make sure you use both battery and

AC power at the same time. With the battery

alone, the parent unit can cordlessly run for a

short time only.

NOTE

S

• Use only the battery supplied with this product.

• If the parent unit will not be used for a long time,

disconnect and remove the battery to prevent

possible leakage.

Install the battery as shown below.

NOTES

• Press down on the battery compartment cover to

pull it out.

THIS SIDE UP

NOTES

• Make sure the label THIS SIDE UP is facing up

while inserting the battery.

Replace the battery

To replace the battery, pull out the battery

compartment cover, and then lift up the

battery. Follow the steps above to install the

new battery.

Connect and charge the

battery

NOTE

S

• Use only the power adapters supplied with this

product.

• Make sure the electrical outlets are not controlled

by wall switches.

• The power adapters are intended to be correctly

oriented in a vertical or floor mount position. The

prongs are not designed to hold the plug in place if

they are plugged into a ceiling, under-the-table or

cabinet outlet.

• Make sure the parent unit, the baby unit and the

power adapter cords are out of reach of children.

Connect the baby monitor

Charge the parent unit battery

When you have connected the parent unit

and installed its battery for the first time or

after power outage, the parent unit powers on

automatically. The battery icon indicates the

battery status (see the following table).

NOTE

S

• The parent unit battery is fully charged after

11 hours of continuous charging.

• It takes longer to charge the battery when the

parent unit is turned on. To shorten the charging

time, turn the parent unit off while charging.

• The standby time varies depending on the

volume level you set, your actual use and the

age of the battery.

Battery

indicators

Battery

status

Action

The battery

icon is off

and

displays.

No battery

is installed

but operates

using AC

power, or the

battery has

been installed

incorrectly.

Install the

parent unit

battery.

Charge

without

interruption

(at least 30

minutes).

The screen

displays

Battery low

at Parent

Unit and .

The light

flashes.

The battery

has very little

charge and

may be used

for only a

short time.

Charge

without

interruption

(about 30

minutes).

The battery

icon

becomes

solid .

The battery is

fully charged.

To keep

the battery

charged,

connect it to

AC power

when not in

use.

Before use

NOTES

• This baby monitor is intended as an aid. It is not a

substitute for proper adult supervision, and should

not be used as such.

Test your baby monitor

You may test the baby monitor before initial

use, and at regular times thereafter.

CAUTION

• For hearing protection, make sure the parent

unit is more than 3 feet (1 meter) away from

both baby units. If you hear any high-pitched

noise, move the parent unit further until the

noise stops. You can also press VOL- on the

parent unit to lower or mute the noise.

1. Make sure your baby units and parent unit

are on.

2. The parent unit displays images from the

baby unit.

• Speak towards the microphone of the

baby unit. You will hear the sound at the

parent unit.

3. If you have two baby units, press at the

right side of your parent unit. The screen

switches to other baby unit. Then, repeat

step 2.

NOTES

• When the parent unit displays No link to Camera,

and the LINK LED light flashes, move the

parent unit closer to the baby units (observe the

minimum distance of 3 feet/ 1 meter). You can

also check if the baby monitor is connected to a

live power socket and switched on.

TIP

• Increase the speaker volume of the parent unit if

you cannot hear the sounds transmitted from the

baby units.

Positioning the baby monitor

CAUTION

• Keep the baby unit out of the reach of your baby.

Never place or mount the baby unit inside the

baby’s crib or playpen.

NOTE

• To avoid interference from other electronic

devices, place your baby monitor far away from

devices such as wireless routers, microwaves,

cell phones and computers.

1. Place the baby units more than 3 feet

(1 meter) away from your baby.

2. Adjust the angle of the baby unit camera to

aim at your baby.

3. Place the parent unit more than 3 feet

(1 meter) away from the baby units.

CAUTION

• The default volume of your parent unit is level

3, and the maximum volume is level 5. If you

experience high-pitched screeching noise from

your baby monitor while positioning:

- Make sure your baby units and parent unit are

more than 3 feet (1 meter) apart, OR

- Turn down the volume of your parent unit.

Operating range

The operating range of the baby monitor is

up to 1,000 feet (300 meters) outdoors or

160 feet (50 meters) indoors. The actual

operating range may vary depending on

the environmental conditions and other

interferences such as walls, doors and other

obstructions.

Overview

Baby unit overview

1

Light sensor

2

Camera

3

Infrared LEDs

4

Microphone

5

Speaker

6

Antenna

• For signal reception.

7

Temperature sensor

8

ON/OFF LED light

• On when the baby unit is turned on

and is paired to the parent unit.

• Flashes when the baby unit is not

being viewed; or when the link to the

parent unit is lost.

9

ON/OFF switch

• Slide to turn on or off the baby unit.

10

Power jack

11 Threaded socket

• For wall mount installation use.

12

PAIR

• Your baby units and parent unit

provided are already paired.

Parent unit overview

1

LED lights

• Indicate the different statuses of

the parent unit. For details, refer to

Parent unit lights.

2

LCD display

3

Zoom

• Press to zoom in or out while

viewing image in.

4

• Press to change the screen to view

images from different baby units.

• For VM3261-2 only.

LCD ON/OFF

• Press and hold to turn on or off the

LCD screen.

5

MENU/SELECT

• Press to enter/exit the menu.

• While in a sub-menu, press to

choose an item, or save a setting.

6

Microphone

7

• While in a menu, press to scroll up,

or to enter an item’s sub-menu.

• While zooming, press and hold to

move the zoomed image upward.

• While in a menu, press to scroll

down.

• While zooming, press and hold to

move the zoomed image downward.

• While in a menu, press to choose

the next item on the left, or enter

into the submenu, if any.

• While zooming, press and hold to

move the zoomed image leftward.

• While in a menu, press to choose

the next item on the right, or return

to the main menu while in submenu.

• While zooming, press and hold to

move the zoomed image rightward.

8

On/off

• Press and hold to power on.

• Press and hold again to power off.

9

TALK

• Press and hold to talk to the

selected baby unit.

10

VOL-

• Turn down the volume when the

speaker is on.

11

VOL+

• Turn up the volume when the

speaker is on.

12

Speaker

13

Power jack

14

Battery compartment cover

15

Stand

Parent unit lights

LINK

On when the parent unit is linked to

the baby unit.

Flashes quickly when the link to the

baby unit is nearly lost.

On when the parent unit is

connected to AC power, or the

battery is charging.

Flashes when the parent unit

battery is low and needs charging.

Off when the parent unit is

disconnected from AC power.

On when the speaker volume of the

parent unit is turned off.

TALK

On when the parent unit is talking to

the baby unit.

Parent unit status icons

Connection status

• or displays when strong

signal strength is detected

between the baby unit and the

parent unit.

• or displays when moderate

or low signal strength is detected

between the baby unit and the

parent unit.

Patrol mode

• Displays when the parent unit is in

PATROL mode.

• For VM3261-2 only.

or

or

or

Current view status

• Displays the number of the baby

unit that is being viewed.

Zoom

• Displays when the current image

on the parent unit has zoomed in.

Night vision

• Displays when the baby unit being

viewed has activated the night

vision feature.

Lullaby

• Displays when a lullaby is playing.

Talkback

• Displays when talking back to the

baby units from parent unit.

6-level sound indicator

Displays the sound level according

to the scales of loudness when there

is sound transmitted from the baby

unit.

• (1 to 2 bars) indicates low sound

level detected by the baby unit.

• (3 to 4 bars) indicates

moderate sound level detected by

the baby unit.

• (5 to 6 bars) indicates high

sound level detected by the baby

unit (e.g. baby crying loudly).

Mute alert

• Displays when the parent unit

speaker volume is set to off.

or

Real-time temperature

• Displays the real-time temperature

detected by the baby unit in

Fahrenheit (

o

F) or Celsius (

o

C)

(e.g. 57

o

F or 14

o

C).

Battery status

• animates

when the battery is charging.

• displays solid when the

battery is fully charged.

• displays when the battery is

low and needs charging.

AC power without battery

• Displays when the parent unit is

connected to AC power without

the battery.

Speaker volume

• Displays the parent unit speaker

volume level while adjusting.

Parent unit main menu icons

Brightness

You can change the brightness of

the parent unit screen.

LCD screen off timer

You can set a specific time to

screen off your parent unit.

Temperature

You can turn on the temperature

alert tone so that the parent

unit beeps whenever the room

temperature detected by the baby

unit falls outside of the desired

temperature range.

You can choose to display the

temperature in Fahrenheit (

o

F) or

Celsius (

o

C), or set the maximum/

minimum temperature limit for

alerts.

Lullaby

You can select, play, or stop a

lullaby.

VOX sensitivity

With this feature, you can choose

to hear sounds from the baby unit

all the time, or to hear sounds

that exceed a certain level. You

can use the parent unit to adjust

the microphone sensitivity of

your baby unit. The higher the

sensitivity level, the more sensitive

the baby unit is in detecting

sounds for transmitting to the

parent unit.

Sound-activation screen

When the baby unit being viewed

detects no sound, the parent

unit screen stays off to save

power. Once a sound is detected,

the parent unit screen turns on

automatically. It will then turn

off again after 50 seconds of no

sound detection.

Patrol mode

You can monitor your baby in

PATROL mode.

Parent unit warning icons and

messages

No link to Camera

The selected baby unit is

out of range or is turned

off.

/Battery low

at Parent Unit

The battery is empty and

needs to be recharged.

Operation is in progress.

/Temperature

too high

or

/Temperature

too low

The temperature detected

by the baby unit is higher/

lower than the desired

temperature alert range.

The parent unit is

searching for baby units.

Using the baby monitor

Power on or off the baby unit

• Slide the ON/OFF switch to ON to turn

on the baby unit. The POWER LED light

turns on.

• Slide the ON/OFF switch to OFF to turn

off the baby unit. The POWER LED light

turns off.

Power on or off the parent unit

• Press and hold to turn on the parent unit.

The screen turns on.

• Press and hold again to turn off the

parent unit. The screen turns off.

Turn on or off the parent unit

screen

You can turn on or off the parent unit screen

without powering off the parent unit. You can

still hear sound from the baby unit.

• Press and hold LCD ON/OFF on the parent

unit to turn off the screen.

• Press any key on the parent unit to turn on

the screen again.

Screen off timer

You can set the screen off time for the parent

unit when there is no key press for a specific

time interval.

When the screen is turned off, you can still hear

sound from the baby unit.

1. Press MENU when the parent unit is idle.

2. Press or to choose , then press .

3. Press or to choose the desired time

period to time off screen ( / / /

), then press SELECT to confirm your

selection.

Adjust LCD brightness

You can change the brightness of the parent

unit screen from Level 1 to Level 5. The LCD

brightness is preset to Level 3.

1. Press MENU when the parent unit is idle.

2. Press or to choose , then press .

3. Press or to choose the desired level of

brightness, then press SELECT to confirm

your selection.

Adjust the sound sensitivity of

the baby unit

You can choose to hear sounds from the baby

unit all the time, or to hear sounds that exceed

a certain level. You can use the parent unit to

adjust the microphone sensitivity of your baby

unit. The higher the sensitivity level, the more

sensitive the baby unit is in detecting sounds

for transmitting to the parent unit. The VOX

sound sensitivity is preset to the highest level.

Sensitivity

Level

Description

Highest

Low

sensitivity

High

sensitivity

Highest VOX sensitivity

level

The parent unit speaker

is constantly on, and

you will hear all sounds

(including background

noises) from your baby’s

room.

High

High VOX sensitivity

level

The parent unit speaker

turns on for soft babbling

and louder sounds from

your baby. It remains quiet

when your baby sleeps

soundly.

Medium

Medium VOX sensitivity

level

The parent unit speaker

turns on for loud babbling

and louder sounds from

your baby. It remains

quiet when your baby

makes soft sounds.

Low

Low VOX sensitivity

level

The parent unit speaker

turns on for crying and

louder sounds from your

baby. It remains quiet

when your baby makes

soft sounds.

Lowest

Lowest VOX sensitivity

level

The parent unit speaker

turns on for loud crying

or screeching sounds

from your baby. It remains

quiet when your baby

makes soft sounds.

1. Press MENU when the parent unit is idle.

2. Press or to choose , then press .

3. Press or to choose the desired

sensitivity level, then press SELECT to

confirm your selection.

TIP

• You can adjust the baby unit placement to

improve the sound detection.

Turn on or off the sound

activation

When sound activation is on, as long as no

sound is detected within 50 seconds, the

parent unit screen will turn off automatically to

save power.

When your baby unit detects a sound, which

exceeds the selected sensitivity level, the

sound activation triggers the parent unit screen

to turn on automatically. When no sound is

detected within 50 seconds, the screen will be

off again.

1. Press MENU when the parent unit is idle.

2. Press or to choose , then press .

3. Press or to choose or , then

press SELECT to confirm your selection.

NOTES

• If the sound sensitivity is set to the highest level,

or lullaby is playing, the parent unit screen may

remain on continuously even though sound

activation is on. This depends on whether the

baby unit detects any sounds.

Adjust speaker volume

For parent unit:

• Press VOL-/VOL+ on the parent unit to

adjust the speaker volume.

NOTE

• When the parent unit speaker volume is set to

zero, appears on the screen and the light

turns on.

For baby unit:

The baby unit speaker volume determines the

lullaby and talkback volume transmitted from

your parent unit.

1. Press MENU when the parent unit is idle.

2. Press or to choose , then press .

3. Press to choose .

4. Press or to choose the volume level of

the lullaby on the baby unit.

5. Press SELECT to confirm your selection.

Monitoring mode

* For VM3261-2 only.

Every time the parent unit is turned on, it

displays a baby unit in SINGLE-CAM mode.

If there are two baby units in your system, you

can also monitor your baby in PATROL mode.

SINGLE-CAM

The screen displays

image of a single baby

unit in full screen.

PATROL

A single cam view that

transits to a different baby

unit every 10 seconds.

In SINGLE-CAM mode:

• Press to switch to another camera if

you are in SINGLE-CAM mode.

Press .

In PATROL mode:

1. Press MENU when the parent unit is idle.

2. Press or to choose , then press .

3. Press or to switch on or off PATROL

mode, then press SELECT to confirm your

selection.

10s

BC

User’s manual

VM3261

VM3261-2

Video Monitor

Go to www.vtechphones.com

to register your product for

enhanced warranty support and

the latest VTech product news.

> 1m (3ft)

b

c

d

e

f

n

o

l

k

j

m

a

i

h

g

1

4

8

9

11

10

12

2

3

5

6

7

> More than 3 feet

(1 meter)

THIS SIDE UP

THIS SIDE UP

1 set for VM3261

2 sets for VM3261-2

1

4

8

9

11

10

12

2

3

5

6

7

b

c

d

e

f

n

o

l

k

j

m

a

i

h

g

＜3ft (1m)

＞ 3ft (1m)

1

4

8

9

11

10

12

2

3

5

6

7

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Vtech VM3261 Babyfoon. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Vtech. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Vtech VM3261 Babyfoon in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Vtech Babyfoons
Meer handleidingen voor Babyfoons

Veelgestelde vragen over Vtech VM3261 Babyfoon

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Vtech VM3261-2 Babyfoon

Handleiding

Vtech VM5251-2 Babyfoon

Handleiding

Vtech VM3251 Babyfoon

Handleiding

Vtech VM301 Babyfoon

Handleiding

Vtech TM8212 Babyfoon

Handleiding

Vtech VM3251-2 Babyfoon

Handleiding

Vtech TM8212-2 Babyfoon

Handleiding

Vtech VM303 Babyfoon

Gerelateerde categorieën