Handleiding Yongnuo Speedlite YN565EX Flitser

Handleiding

YN565EX

SPEEDLITE

ＵＳＥＲ　ＭＡＮＵＡＬ

Before use, please READ this user manual carefully in order to ensure

your safety. Keep it properly for reference in the future.

To avoid fire or electrical shock, do not expose this product to rain or moisture.

To avoid short circuit, be sure the batteries contacts are securely packed and in accordance

with local provision when handling the batteries.

Please place the batteries and the parts which can be swallowed mistakenly away from children.

Contact a doctor immediately when it occurs.

To avoid possible injury to eyes, do not use the flash light in a short distance from the eyes.

To avoid possible safety accident, do not use the flash light on the people who need a high

degree of attention.

Please take out the batteries and stop using immediately in case of below.

● This product is dropped or shocked seriously and the inner part of the product is bared.

● If the battery leaks corrosive liquids, please take out the battery with gloves.

● The product gives off strange smell, smokes or heats.

Do not disassemble or maintain this product. Touching the internal high voltage circuit

will cause electric shock.

Remove batteries during long periods of non-use.

I. Warning

-1-

-2-

-3-

-4-

-5-

-6-

-7-

-8-

-9-

-10-

-11-

-12-

-13-

-14-

-15-

-16-

II．Features

AWL SUPPORTED FOR N’s & C’s SYSTEM

The YN565EX can be triggered by 580EX II, SB-900/800/700, 7D/60D/600D, Nikon c-command and

ST-E2, and flashes as TTL mode as well as M/Multi mode.

TTL FLASH WITH LARGE GUIDE NUMBER

GN58@ ISO100, 105mm; which reaches the level of the mainstream hot shoe flashes, supports TTL/

M/Multi mode.

MULTIPLE TRIGGER MODE SUPPORTED

The YN565EX can be triggered by hot-shoe, flash command slave mode, optical S1, and S2

(pre-flash-canceled mode).

SUPPORTS AUTO/MANUAL ZOOMING

The YN565EX covers a focal length range of auto, and 24 to 105mm, supports full-frame/half-frame

camera.

COMPREHENSIVELY SUPPORTS TTL FUNCTIONS

FEC, FEB, Rear-curtain sync, FE lock, Modeling Light, Canon camera menu accessable

SUPER SPEED OF CHARGING RECYCLE

It only takes 3 seconds to finish a charging cycle after a full level output, you can use external power

pack to accelerate the charging speed once more.

PROVIDES CHARGING SOCKET FOR EXTERNAL POWER PACK

YN565EX provides charging socket for external power pack, to meet your higher demand for

charging recycle.

PC PORT PROVIDED

YN565EX provides PC port，you can make the flash synchronously by connecting to the PC port.

SOUND PROMPT SYSTEM

Turn on the sound prompt function, different sounds indicate working situations help you focus on

shooting.

MODELING LIGHT FUNCTION

Press down the camera’s depth-of-fired preview button, the YN565EX will send out continuous flash

lasting one second.

ADVANCED SETTINGS ON FLASH

The YN565EX supports advanced settings; you can customize the unit according to your shooting

preferences.

AUTOMATIC SETTINGS SAVING

YN565EX can save the current settings automatically.

LCD PANEL USER INTERFACE WITH SUPER GELIVABLE METAL HOT-SHOE STAND

III．Quick Start

If you don’t have much time to read the whole user manual, we advise you to read this section.

1. Please avoid the excessive use of the output with maximum power. It can effectively extend the service

life of this product.

2. You can understand the function of each button by pressing them and observing the displayed content.

3. Keeping [ZOOM] button under pressed can enter off mode SL（cn or c, n separately）/S1/S2.

4. Long press on [Fn] button to set the function of advanced option of speedlite. See the section of

“advanced setting” for the content.

5. Operate the YN565EX through function setting of external speedlite on the menu of Canon camera.

6. Press the [UP], [DOWN], [LEFT] and [RIGHT] buttons to adjust the parameters of speedlite quickly at

the current mode. For some parameters, the [OK] button in the center is needed to be pressed for setting.

7. This product provides ETTL/M/MULTI mode. It can be switched through [MODE] button.

IV. Nomenclature

1．Reflection board

2．Wide-angle diffuser

3．Flash head

4．External power pack socket

(It can be connected to the

SF-18C or SF-17C external

power pack)

5．PC port（for input）

6．Contact cover

7. Wireless sensor

8．Battery chamber’s cover

9. AF-assist beam emitter

10．Locking ring

11．Hot shoe stand

12．Hot shoe contact

13. Sound port

14. LCD panel: It will display the status of function settings.

15. Rear-curtain sync hotkey: The speedlite will be switched between rear-curtain sync and front-curtain

sync in circle for each press.

16. ZOOM button: It is applied to set focal length coverage of speedlite and relevant parameters of slave

unit. Use the [ZOOM] and [LEFT], [RIGHT], [UP], [DOWN] and [OK] button for operation.

17. Power switch: The power of the speedlite can be turned on or turned off by holding this button for

2 seconds.

18. Select/Setting button group: Buttons of multi functions include LEFT, RIGHT, UP , DOWN and OK

buttons; you can adjust output, FEC, FEB, Stroboscopic flash count, Stroboscopic flash frequency,

zooming setting, slave units, channel and slave groups.

19. Mode switch button: Under the normal flash, the mode of the speelite will be switched among the

ETTL/M/MULTI in circle for each press; and under the wireless flash, long press on this button locks

the speedlite in M and MULTI mode.

20. Illumination/Advanced options button: A short press will turn on or turn off the LCD panel

illumination light, a long press on the button conducts advanced option setting of speedlite.

21. Charging indicator / Test button: The lighting of red light shows that charging process is finished

and flash can be used; the lighting of green light shows that it is in charging or a shortage of power;

the alternate flashing of the red and green lights shows overheat protection, please wait for about 3

minutes to cancel the protection before continuing use. If you press this test button (PILOT), the

speedlite will give a test flash.

22. Flash exposure confirmation indicator: If a standard exposure was obtained, the flash exposure

confirmation indicator will light for 3 seconds.

液晶屏

V. Installation Instruction

1. Install Batteries

Slide the batteries chamber’s cover in the direction of the arrow.

Insert the batteries according to the label inside battery chamber.

Make sure the direction of the batteries’ polarity is correct.

Close the battery chamber cover in the direction of the arrow.

2. Attaching to the Camera

Loosen the locking ring by turning it in the direction of the arrow.

Slip the speedlite hot shoe stand into the camera hot shoe stand until it stops.

Turn the locking ring in the direction of the arrow tighten.

To detach the speedlite, loosen the locking ring by turning it in the opposite direction.

VI. Basic Functions

1. Basic Operations

2. Power-on and Power-off

The power of the flash light can be opened or closed by holding this button for 2 seconds. It is suggested that the

battery shall be taken out after the power of the flash light is closed through this button.

After opening the power switch of the flash, the flash will fetch the setting state saved in the closedown last time, the

charging indicator is green, which indicates the flash is available.

If the charging is not completed within 20 seconds, and <PL> will be displayed on LCD panel,the flash will

automatically shutdown. Then you need to replace with new batteries.

You may press the testing button PILOT to test whether the flash works normally.

After use, hold the power switch for 2S to power off.

3. ETTL MODE

Just set the camera’s shooting mode to [AV] (aperture-priority AE), [TV] (shutter-priority-AE), or [M](manual), and

you can use ETTL autoflash. Under the ETTL mode, YN565EX supports FEC, FEB, Rear-sync, FEV, Modeling,

Canon camera menu accessable.

4. M mode

You can set the flash output from 1/128 to 1/1 full power in 1/3-stop

increments. Press the [LEFT] [RIGHT] button to adjust the output directly.

�Press [MODE] button and the <M> will display on LCD panel.

�Press [LEFT] and [RIGHT] button to adjust output level, you can fine tune the power output of the flash by

[UP] and [DOWN], the step size is 1/3ev.

Press the shutter button halfway, and check that the subject is within

the effective range displayed on the LCD panel.

NOTE：The effective range don’t display on the LCD panel before

charging is finished.

*

*

*

5.MULTI mode

With MULTI mode, a rapid series of flashes is fired. It can be used to capture multiple images of a moving subject

in single photograph.

The speedlite will flash according to the output power, flash times

and frequency you set. Use [LEFT], [RIGHT] and [OK] buttons to

adjust output power, flash times and frequency. The adjustment

scope of output frequency is 1/128-1/64-1/32-1/16-1/8-1/4, the

scope of flash times is from 1 to 100 (if the flash time is set as --,

it flashes according to the default setting.) and the scope of flash

frequency is 1 to 100.

Adjustment method: please press [OK] button to select setting items

(flash) and use the [LEFT] and [RIGHT] buttons to adjust the

parameters. After the setting is completed, press [OK] button to

confirm the setting.

NOTE:The charging speed of flash light is slow under the situation

that the electricity quantity of the battery is insufficient, which may

cause the occurrence of the high-frequency flash. Please reduce

the flash frequency or change new battery under this situation.

6. S1/S2 mode

These two modes are suitable for manual flash environment and TTL flash environment respectively.

Under these two modes, the way to adjust the output level is like the way in M mode.

When using S1/S2 mode, you can rotate the flash head to make the wireless triggering sensor face with

the master flash. Setting method: Hold press the [ZOOM] button, and then press [LEFT] [RIHGT] button

to select S1 or S2.

S1 mode: It will work with the first trigger of master flash synchronously; the master flash should be set

at manual flash.

S2 mode: It is also called “pre-flash cancel mode”, it can neglect the pre-flash given by TTL flash, and

therefore, it can support the main flash working in TTL mode.

The following situation shall be avoided when the S1 and S2 modes are used: the red eye reduction

function of the main light is used; the order mode (nikon) or wireless mode (canon) of the main light is

used; the ST-E2 is used as the flash controller. Otherwise, please set the speedlite as SL (see “wireless

flash system” for detail).

11. ZOOM Setting the Flash Coverage

Auto Zoom: Press the [ZOOM] button to adjust the flash

overage, if <M> is not displayed, the flash coverage will

be set automatically (35mm for default coverage).

Attaching the speedlite to the camera, the flash coverage

will set automatically to match the lens focal length.

Manually set the zooming position: Press the [ZOOM] button to

adjust the flash coverage, if <M> is displayed, pressing the

[LEFT] [RIGHT] or [UP] [DOWN] buttons, the coverage focal

length of the flash will switch in circle of (24, 28, 35, 50, 70, 80,

105mm).

NOTE: Using wide-angle-diffuser, the flash coverage will then

be extended for 14mm.

12. Sound prompt

When the sound prompt function is activated the speedlite will give out different sound to indicate the working state.

Sound prompt can be set through function of advanced option. The method is: long press on the [Advanced option]

button until it enters the advanced option setting state. Select item 14 through [UP] and [DOWN] buttons and use

[LEFT] and [RIGHT] buttons to set sound disabled or sound enabled. <14 S0 nd on/-- >. This means that the sound

prompt is enabled or disabled. When the sound prompt is enabled, see the following table for the meaning of sound.

VII. Wireless Flash System

YN565EX has wireless remote flash systems as slave unit, the YN565EX can be triggered by 580EX II, SB-900/800/

700, 7D/60D/600D, Nikon c-command and ST-E2, wireless TTL or manual lighting can be achieved.

cn: Indicating that it can receive wireless signal from Canon system as well as Nikon system at the same time.

c: Indicating that it can only receive wireless signal from Canon system, avoiding Nikon system.

n: Indicating that it can only receive wireless signal from Nikon system, avoiding Canon system.

Any flash exposure compensation, FEB, FE lock, manual flash, and stroboscopic flash settings set with the master

unit will be automatically transmitted to the YN565EX.

Even with multiple YN565EXs, all of them will be controlled in the same way via wireless signal.

Wireless flash of two slave units made up by YN565EX

�Wireless option setting: cn, c, n for operation

�Communication Channel setting: 1, 2, 3, 4

�Groups setting: Set one YN565EX as group A, and set the

other one as group B.

�Master unit setting: Set the communication channel, Set the

flash ratio of master unit A：B or A：B C. You can conduct

flash shooting.

*

*

*

*

A

B

Indoors

Outdoors

A

B

C

Indoors

Outdoors

Wireless flash with three YN565EX speedlites

Wireless option setting: cn, c, n

Channel setting: 1, 2, 3, 4

Groups setting: Set three YN565EX speedlites as group A,

group B and group C respectively.

Setting master and shooting: Please select the ratio<A: B C>.

Press the test button of master to test whether the flash works

normally; if the flash does not fire, adjust the slave unit’s

angle toward the master unit and distance from the master unit.

*

*

*

*

NOTE: If ratio <A: B> is set, the slave unit in group C will not fire.

If you have the slave group set to <A> for three slave units, all three slave units will be controlled as if they were

one speedlite in slave group A.

4. Setting Manual Flash and Stroboscopic Flash with Wireless

You can also lock the flash mode when YN565EX is used as slave unit.

Manual flash: Press the [MODE] button for 2 sec. or longer until

<M> display, then you can set the output level by pressing

[LEFT] [RIGHT] [UP] [DOWN].

Stroboscopic flash: Continue to press the [MODE] button

until <MULTI> display, then you can set the output level,

number offlashes, and firing frequency by pressing [OK]

[LEFT] [RIGHT].

5. Shooting Examples with Wireless Flash System

Master unit: 580-II, SB-900/800/700, 7D/60D/600D with built-in commander mode, Nikon c-commander and

ST-E2.

Slave unit: YONGNUO EX series flash, you can create three slave groups at all.

Use the mini flash stand (tripod socket provided) to prop up the YN565EX speedlite.

Swing the YN565EX so that its wireless sensor faces the master unit.

Indoors, the wireless signal can also bounce off the wall so there is more leeway in positioning the YN565EX(s).

After positioning the YN565EX(s), be sure to test the wireless flash operation before shooting.

Don’t place any obstacles between the master unit and slave unit(s). Obstacles can block the transmission of

wireless signals.

Indoors

Outdoors

25m

15m

*

*

*

*

*

*

*

VIII. The Advanced Application

1. Ultra-long-range Wireless Flash

YN565EX can receive remote wireless signal. The longest distance used indoors is 25 meters and the longest distance

used outdoors is 15 meters.

Please note that the YN565EX’s wireless sensor should be faced to master unit, and make sure it is within the effective

range of transmission.

2. Flash Exposure Compensation

You can use the exposure compensation function of the camera to compensate flash output so as to make shooting

effect better meet your requirements. You can also make compensation of flash brightness with the [LEFT] [RIGHT]

button within the range of ±5ev, with the precision of 1/3ev. Every press the button, the compensation setting will be

displayed on LCD panel.

NOTE: For Canon version, please note that this compensation setting will override the exposure compensation setting

on the camera.

3. Rear- curtain Sync

You can use slow-speed shutter to produce trailing smear for the object and the flash light will flash at the moment

when the shutter is going to be shut, which means the rear-curtain sync function .(For the rear-curtain sync setting,

refer to your camera manual for setting). You can turn on or turn off the rear-curtain sync by pressing the [rear-curtain

sync] hotkey on panel of YN565EX.

NOTE: When YN565EX is used as slave unit, the rear-curtain sync function cannot be set.

4. Exposure Bracketing (FEB)

The FEB function is set on the camera or speedlite. For the specific setting method, refer to your Camera Instructions.

After the FEB is set, after 3 photos are taken, exposure compensation will be made automatically in the sequence of,

for example, “normal � under � over”. This function helps you improve the success rate of photo taking.

The setting method on the YN565EX speedlite: Press the [UP] [DOWN] button to adjust the exposure bracketing

amount.

NOTE: For FEB, set the camera’s drive mode to single shooting. Be sure the flash is ready before shooting.

5. FE Lock (Canon)

To use this function, cover the subject for which flash exposure will be locked at the center of the viewfinder of

camera, press the button <*> of the flash exposure lock, and the flash light will pre-flash and the camera will calculate

the appropriate flash output data. Now you have some time for decomposition, after which, you can take photo.

(The function can be used only when it is supported by your camera. For the setting method, refer to your Camera

Instructions.)

6. FV Lock (Nikon)

Set the AE-L/AF-L function as FV Lock on the camera before using this function. At this time, you can aim at your

desired object in the viewfinder and then press the AE-L key or AF-L key, in such case, the flash light will pre-flash

to get the reading of flash exposure for the object; after you have confirmed the scene frame, press the shutter.

(This function can only be available when your camera supports it; for the setting of AE-L and AF-L,

refer to your camera manual).

7. Advanced Setting

The YN565EX provides advanced settings, you can customize speedlite feature to suit your shooting preferences.

Set the advanced settings through hotkey of speedlite or menu accessable. Setting method of hotkey: Press the

[advanced setting] button for 2 sec. or longer until the item to be set displays; for example, <01 SL EP --> is displayed.

Menu accessable can only be available when your camera supports it; for the setting method, refer to your camera

manualHold the [OK] button to recover the default settings.

The meanings of the items can be found in the table below:

● Fn NO.： 00

●Effective flash distance：effective flash distance takes

m as unit or ft as unit.

● Fn NO.： 01

● SL EP on： Auto power off is enabled

● SL EP --： Auto power off is disabled

● Fn NO.：03

● Fb CL on：FEB auto cancel is enabled

● Fb CL --： FEB auto cancel is disabled

● Fn NO.：04

● Fb 0 － +：Sequence of FEB is “0 → － → +”

● Fb －0 +：Sequence of FEB is “－→ 0 → +”

● Fn NO.: 08

● AF L on：AF-assist beam firing is enabled

● AF L --： AF-assist beam firing is disabled

●Fn NO.：09

● AP S – A1：Automatic identification is enabled

● AP S – --：Disable

● Fn NO.：10

● SL Sd 60：Power automatic off of the slave unit is 60 minutes

● SL Sd 10：Power automatic off of the slave unit is 10 minutes

● Fn NO.：11

●SL OFF 8H：Slave auto power off cancel within 8 hours

● SL OFF 1H：Slave auto power off cancel within 1 hour

● Fn NO.：14

● SO nd on：Sound prompt function is enabled

● SO nd --： Sound prompt function is disabled

● Fn NO.：15

● SEOFF 3/5/10/30/1H/2H/3H/5H：Keeping idle for 3/5/

10/30 minutes or 1/2/3/5 hours will enter the dormancy mode.

● Fn NO.：16

● CL EA --：Recover the default settings

NOTE: The option with Fn number from 00 to 13 can be set through “Flash C. Fn settings” of camera menu;

the option with number 02, 05, 06, 07, 12, 13 are be disabled.

8. The use of external charging box

You can buy YONGNUO external charging boxes like SF-18C or SF-17C and connect it to the charging port of the

speedlite. After flash, the charging box will charge the speedlite.

9. High-speed continuous shooting

The flash can realize the high-speed continuous shooting function. Please set the camera in the continuous shooting

form and then shoot. Please turn off the sound prompt function when using high-speedlite continuous shooting.

Please note: The number of photos that can be continuous shot is related with the output level. Please use the fully

charged battery.

10. Reflection Flash

Bounce flash means to take photos by making flash light head aimed

at wall or ceiling and using the light reflected back from the ceiling

or wall to light the desired object, so that the shade behind the object

can be decreased to get more natural shooting effect.

If the wall or ceiling is too far, the bounce flash may be too weak to

get enough exposure. The wall or ceiling should be even and white

in order to get efficient reflection; if the reflection surface is not

white, color cast may appear in photo.

-17-

-18-

11. Use Reflection Board to Take Photos

With the reflection board flash, draw the reflection board and the wide-angle

diffusion board out from the light head at the same time and then push the

wide-angle diffusion board back. In such case, if this product is being used to

take photos, it will produce a highlighted point on the eyes of the subject and

thus make the eyes charming (catch light). This function can reach optimal

effect when the flash head is up 90°.

9. Use Wide-angle Diffuser

Pull out the wide-angle diffusion board, push back the reflection board and

arrange them as per the figure; in such case, the flash scopes will extent to

18 mm and the flash effect will be softer and more natural.

Guide Number of different focal length range (at ISO 100, in meters / feet)

X. Possible problems during use and solutions

1. The YN565EX can’t flash

�Check whether the batteries are installed in the correct orientation: Please install the batteries in the correct

orientation.

�Check whether the speedlite is attached to the camera: Slip the speedlite hot shoe stand into the camera hot shoe

stand hard.

Check the hot shoe contact: Clean the contacts.

�Check whether the batteries are exhausted: If the charging is not completed within 20 seconds, the flash will

automatically shutdown. Then you need to replace with new batteries.

*

*

*

*

2. YN565EX can’t work as slave unit

�Check the slave unit setting: The YN565EX must be set to SLAVE.

�Check the slave unit’s situation: Please position the YN565EX(s) within the master’s wireless transmission range.

Adjust the slave unit’s angle toward the master unit and distance from the master unit.

Note: Setting the slave unit as separate c or n can slightly improve the success rate of flash.

*

*

3. Underexposure or overexposure of photo

� Check whether the shutter, aperture and sensitivity (ISO) of camera are set too close to the limit of flashing, or

whether the exposure compensation, exposure bracketing and other settings relative with flashing are correct.

� Because of the differences among different types of cameras and the personal preference, you may meet the whole

overexposure or underexposure when using this product, and so try to adjust it through the flashing compensation

or exposure compensation.

*

*

-19-

4. Is the FEB exposure range set anew every time?

You can access FEB setting through camera menu or lock FEB setting through Fn advanced option setting to avoid

that FEB will cancel automatically when completing three shooting tasks. The number of setting option is 03.

It is ok to set the “FEB auto cancel” disabled.

5. Underexposure of photo

Please check whether your speedlite is set with exposure bracketing and the exposure order is “－→0→＋”.

You can access Fn advanced option through camera menu to set the order of exposure bracketing as “0→－→＋”

or enables “ FEB to cancel”.

6. Vignetting appears in photos or only part of the subject is illuminated?

This product has a designed light head zoom range of 24-85 mm, and is currently not compatible with full frame

camera system. You may pull out the wide-angle diffuser to widen the flash range.

7. The state of YN565EX is abnormal.

Please try to turn off the power supply YN565EX and camera. After YN565EX is installed on the hot shoe of

camera, turn on the power supply again. If it is still unusual, please replace the batteries.

Updated version of this manual can be got from http://www.yongnuo.com.cn/usermanual/downloadIndex.htm

The functions of this manual are based on test conditions of our company. Further notice will not be given if the

design and specifications change.

The YONGNUO logo in this manual includes the registered trademark or trademark of

SHENZHEN YONGNUO PHOTOGRAPHY EQUIPMENT Co., Ltd in China or/and other countries (regions).

All other trademarks are the property of their respective owners.

TEL：(086)0755-83762448 Email： [email protected]

FAX：(086)0755-83762765 Website：www.hkyongnuo.com

SHENZHEN YONGNUO PHOTOGRAPHY EQUIPMENT Co., Ltd

-20-

Manual zoom

Aperture

FEB status

Stroboscopic flash count

Stroboscopic flash frequency

Manual flash 1/3-stop

increment indicator

Advanced setting

Zoom focal length

Advanced option NO.

Auto zoom

for image size

Slave group

Flash range scale

Indicator

(meters)

Indicator

(feet)

Slave

Channel

Flash mode

Slave flash

Rear-curtain sync

FEC

Advanced setting

Manual mode/

MULTI mode

ETTL autoflash

FEB

Manual flash output level

Flash exposure compensation amount

FEB compensation amount

Component

Operation

[Power Switch]

Power switch of the flash light. The power of the flash light can be turned on or turned off by holding this button

for 2 seconds.

It is suggested that the battery shall be taken out after the power of the flash light is closed through this button.

[ZOOM] button

A short press on this button makes the speedlite enter electric zoom setting state. Press [LEFT] [RIGHT] or [UP]

[DOWN] buttons to adjust different focal length （auto，24，28，35，50，70，80，105mm）. .

A long press on this button makes the speedlite enter slave unit setting state, you can set it at SL（cn or c，n

separately）and S1/S2. Then press [OK] button to confirm the setting.

[Rear

-

curtain sync]

hotkey

The speedlite will be switched between rear-curtain sync and front-curtain sync in circle for each press.

[MODE] button

Under the normal flash, the mode of the speelite will be switched among the ETTL/M/MULTI in circle for each

press; and under the wireless flash, long press on this button locks the speedlite in M and MULTI mode.

[Illumination/advanced

option] button

A short press will turn on or turn off the LCD panel illumination, hold the button to go into the status of advanced

options.

[LEFT] [RIGHT] and

[OK] button

Used as the button to adjust slave unit, zoom range, flash brightness, Exposure Compensation, stroboscopic flash

times, stroboscopic flash frequency. See the subsequent chapter for relevant operation.

[UP] [DOWN] button

You can set exposure bracketing and zoom range. Under the TTL mode, you can operate [up] and [down] button to

set the exposure bracketing of speedlite. It should be used with [ZOOM] button to set range zoom.

[PILOT] button

Press this test button and the speedlite will test flashing in current output level; under the dormancy state, you can

Operation of the buttons:

7. Menu Access of Camera (only for the more recent Canon models)

You can control the speedlite by accessing to camera menu on the recent canon models which support ETTL. On the

Flash Control Menu, you can set some parameters through “External flash func. setting” and “External flash C. Fn

setting”, for example, Flash mode, Shutter sync, FEB, Flash exp. comp, Zoom, Wireless set, and advanced setting etc.

8. Test Flash

Whether in any mode, you can press PILOT button to test if the speedlite flash normally. When testing the flash, the

speedlite will give flash at relevant output level in accordance with the chosen output power setting.

9. Power Saving Mode

YN565EX provides shrinkable power-saving mode; this power-saving mode can set through long press on[Advanced

option] button. Long press the [Advanced option] to enter the setting state and select the option with number 01

through [up] and [down] buttons. When pressing the [right] button to set the state as SL EP - -, this means to disable

the function of “automatic power off”. When it is set as SL EP on, this means that the function of “automatic power

off” is enabled, the following table lists the power-saving mode that is set through advanced option.

NO. Scope of

Application

Setting options Power saving mode

-- Power saving mode is closed 01

SL EP

All modes

on Power saving mode is open

60 Power automatic off of the slave unit is 60 minutes 10

SL Sd

SL/S1/S2

10 Power automatic off of the slave unit is 10 minutes

1H Slave auto power off cancel within 1 hours 11

SL OFF

SL/S1/S2

8H Slave auto power off cancel within 8 hours

15

SE OFF

Others 3/5/10/30/1H/2

H/3H/5H

Sleep after idle time of 3 minutes/5 minutes/10 minutes/30

minutes/1 hour/2 hours/3 hours/5hours. After it enters the sleep

state, it powers off automatically after keeps the same idle time.

Under the dormancy situation, <SE> will be displayed on LCD panel, you can awake the speedlite

by pressing any button.

10. Overheating Protection

If the speedlite is used too frequently, the overheating protection function will be triggered, the red and green lights

of the charging indicator will blink alternatively, and <O.H> will be displayed on LCD panel, the speedlite will be

locked. In such case, please wait for about 3 minutes to cancel the protection before continuing use.

Please try to use 1/4 output or lower when rapid shooting is needed to prevent the effect on the shooting.

The sound form Meaning Operation

Tick twice a. A standard flash was obtained；

b. The speedlite is started；

Normal

Three ticks, two times The exposure may be over Adjusting exposure compensation or changing

shooting condition

Tick－tick－tick The exposure may be excessive Adjusting exposure setting or shooting condition

Tick—tick

twice—tick twice—

a. The power is not enough；

b. The speedlite is in the charging or

overheating protection state；

Replace the batteries, waiting for the completion

of charging or the protection is canceled

Tick a long sound The speedlite is fully charged and can be

used.

Normal

Tick—tick—tick Sound prompt before turn off Normal

13. Modeling Light Function

Press down the camera’s depth-of-fired preview button, the YN565EX will send out continuous flash lasting one

second.

NOTE: Do not fire the modeling flash more than 10 consecutive times. If you fire the modeling flash 10 consecutive

times, allow the speedlite to rest for 10 to 15 minutes to avoid overheating and deteriorating the flash head.

14. PC synchronous port (for input)

By connecting to the PC port synchronous port, you can make the flash synchronously.

15. Automatic setting saving

The speedlite will automatically save the current setting in order to let you have a simpler use next time after boot.

1. Master unit setting

To use 580EX II, SB-900/800/700, 7D/60D/600D with built-in commander mode, Nikon c-commander and ST-E2.

For the setting method, please refer to your master instructions.

2. Slave unit settin

As the slave unit, when YN565EX is used, the wireless option of speedlite is set as SLAVE.

Setting method: long press on ZOOM for 2 seconds to make the OFF flash on the LCD screen, this means that it is

in the setting state. Use [LEFT] and [RIGHT] buttons to select SL. The LCD screen display cn when [OK] button

is pressed at this moment. This means that it receives the wireless signal from Canon and Nikon at the same time.

Press ZOOM button again and <c n>,< CH > or < A > will flash. This means that it enters setting state of

Canon or Nikon wireless option, communication channel or slave unit. At this moment, use [LEFT] and [RIGHT]

buttons to set slave unit c/n separately, number of communication channel （1，2，3，4）or slave group

（A，B，C）, then press [OK] button to confirm setting.

Prompt: When does it need to set c or n under the off camera mode instead of cn mode?

When other cameraman uses off camera control in the environment, and you don’t want to be bothered. Separate

setting of c or n may slightly improve the correctness of flash control.

3. Multi-Speedlite, Wireless lighting configurations

You can create two or three slave groups to make shooting effect better meet your requirements, and set flash ratio

for ETTL autoflash shooting of master, as well as manual flash output, frequency flash etc.

Circuit design Insulated Gate Bipolar Transistor (IGBT)

Guide No. 58 (ISO 100, 105mm)

Flash mode TTL、M、MULTI

Wireless trigger N’s & C’s wireless system/S1/S2 pre-flash-canceled mode

Wireless triggering distance 20~25m indoor, 10~15m outdoor

Slave groups 3（A, B, and C）

Channels 4

Zoom range auto, 24, 28, 35, 50, 70, 80, 105mm

Vertical rotation angle -7~90 degrees

Horizontal rotation angle 0~270 degrees

Power supply 4×AAsize batteries (Alkaline or Ni-MH are usable)

Lighting times 100~1500 times (AA alkaline cell used)

Recycle time approx 3s (AA alkaline cell used)

Color temperature 5600k

Flash time 1/200s~1/20000s

Flash control 8 levels of output control (1/128~1/1), 22 levels of fine tuning

External interface hot shoe, PC port and eternal charging port

External power YONGNUO external charging boxes like SF-18C, SF-17C

Additional features Rear-curtain sync, FEC, FEB, FEV, modeling flash, manual zoom, auto zoom, sound

prompt, advanced setting, automatically saving setting, PC port, power saving mode

and over heat protection

Dimensions 60×190×78mm (Extended state)

Net weight 380g

Accessories Flash light (1), protecting bag (1), mini stand (1) and manual (1)

IX. Specifications

Flash Coverage (mm) Flash Output

14 24 28 35 50 70 80 105

1/1 15/49.2 28/91.9 30/98.4 39/127.9 42/137.8 50/164 53/173.9 58/190.3

1/2 10.6/34.8 19.8/65 21.2/69.6 27.6/90.7 29.7/97.4 35.4/116.1 37.5/123 41/134.5

1/4 7.5/24.6 14/45.9 15/49.2 19.5/64 21/68.9 25/82 26.5/86.9 29/95.1

1/8 5.3/17.4 9.9/32.5 10.6/34.8 13.7/45.2 14.8/48.6 17.7/58.1 18.7/61.4 20.5/67.3

1/16 3.8/12.5 7/23 7.5/24.6 9.7/32 10.5/34.4 12.5/41 13.3/43.6 14.5/47.6

1/32 2.7/8.9 4.9/16.1 5.3/17.4 6.9/22.7 7.4/24.3 8.8/28.9 9.4/30.8 10.3/33.8

1/64 1.9/6.2 3.5/11.5 3.8/12.5 4.9/16 5.3/17.4 6.3/20.7 6.6/21.7 7.3/24

1/128 1.3/4.3 2.5/8.2 2.7/8.9 3.5/11.4 3.7/12.1 4.4/14.4 4.7/15.4 5.1/16.7

2-A511 Saige Science & Technology Park, North Huaqian Rd, Futian District, Shenzhen, China

GRP=A

GRP=A

GRP=A

Slave group A

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Yongnuo Speedlite YN565EX Flitser. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Yongnuo. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Yongnuo Speedlite YN565EX Flitser in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Yongnuo Flitsers
Meer handleidingen voor Flitsers

Veelgestelde vragen over Yongnuo Speedlite YN565EX Flitser

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Yongnuo Speedlite YN685 Flitser

Handleiding

Yongnuo Speedlite YN468-II Flitser

Handleiding

Yongnuo Speedlite YN600EX-RT Flitser

Handleiding

Yongnuo Speedlite YN560 Flitser

Handleiding

Yongnuo Speedlite YN968EX-RT Flitser

Handleiding

Yongnuo Speedlite YN500EX Flitser

Handleiding

Yongnuo Speedlite YN560 III Flitser

Handleiding

Yongnuo Speedlite YN560 IV Flitser

Gerelateerde categorieën